|
WILTON 10 x 16" HORIZONTAL
MITER CUT-OFF BAND SAW MODEL #7040M
Featuring:
-
With Mitering head, workpiece remains fixed while the head swivels
to cut any angle from 0 to 45 degrees and locks with a quick acting lever.
Photo shown is without Mitering capability.
-
Equipped with Wilton's exclusive swivel control panel which allows the
operator to access controls from the front or back of the machine
-
Standard with Wilton's exclusive 6 contact point blade guide assemblies
for greater accuracy and longer blade life. These adjustable guide
assemblies utilize cam follower bearings mounted on eccentric shafts on both
sides of the blade. Combined with the side bearings are carbide pads, which
are positioned close to the material being cut, guiding the blade on both
sides to guarantee accurate, square cuts. The back of the blade rides on two
load bearings mounted on a pivot shaft enabling both bearings to equally
share the load.
-
Rapid Acting vise for simple, fast, and accurate set up. For standard cut
offs, the ridged design makes square cuts easy. This design improves
operator safety, allows for faster set up, increases through put, thereby
lowering costs per cut. For Mitering no wrenches are needed to set up
the vise. The angle can be pre-adjusted by simply loosening a handle.
-
Standard variable speed drive allows the operator to fine tune the blade
speed to maximize the performance. This again results in higher efficiency
and lower costs per cut.
-
14" dia. cast iron blade wheels
-
Heavy duty transmission utilizes hardened and ground gears operating in an
oil bath. This provides a smooth, quiet drive train and positive SFM to the
blade.
-
The saw is gravity fed but controlled by a dual system of counter-balance
springs working with a hydraulic cylinder to ensure smooth, constant feed
pressure on the blade.
-
3 phase version
|
|
Specifications |
|
Model |
7020M/7040M |
|
Cutting
Capacity: |
10" Round
10" x 10" Square
9" x 16" Rectangle |
|
Blade Size: |
1" x
.035" x 135" |
|
Blade Speeds: |
70 to 190 Feet
per minute - Variable speed |
|
Blade Wheels: |
14"
Diameter/cast Iron |
|
Blade Guides: |
Adjustable 6
point contact combination bearing and carbide |
|
Drive Motor: |
1.5 HP/1 Phase 2
HP/3 Phase |
|
Vise: |
Rapid acting |
|
Coolant System: |
Recirculating
system standard with each machine complete with 1 GPM pump, 8 gallon
reservoir and coolant applied through the blade guides |
|
Machine
Dimensions: |
79" L x
31" W x 41" H |
|
Height of Work
Table: |
25 1/2" |
|
Net Weight: |
1,125 lbs. |
|
Standard Features
-
Variable speed drive system allows the operator to fine-tune the blade speed
fast and easily
-
Exclusive 6 contact point blade adjustable guide assemblies
-
Combined with the side bearings are carbide pads, the back of the blade rides
on two load bearings mounted on a pivot shaft so both bearings share the load
equally.
-
Mitering Head - the workpiece remains fixed while the head swivels to cut any
angle 0°- 45°
-
Heavy duty transmission utilizes hardened and ground gears operating in and
oil bath
-
Counterbalanaced feed system is controlled by a dual system of counterbalance
springs working with a hydraulic cylinder
Standard Equipment
-
Exclusively PATENTED 3 jaw vise allows for faster set-up
-
Recirculating coolant system standard ,1 GPM pump, 8 gallon reservoir and
coolant applied through the blade guides
-
Cast iron blade wheels
|
|

Click here for Bandsaw Blades!
|
|
|
|
|
|
WMH5674022
$103.37 $87.90 
"Replacement Blade for WILTON« 10"" x 16"" Horizontal Bandsaws- 5/8VT x 1"" x.035"" x 135"" - Bi-Metal (WEIGHT = 1.2 lbs ) :::: Please See Shipping Chart at Checkout for Freight or Add to any FREE FREIGHT WMH item for Free Freight on the order. "
|