ICS 613GC Concrete Saw at Southern Tool Catalog

The 613GC from ICS cuts twice the depth of an ordinary circular blade cut-off saw.
Weighing only 21 pounds complete, this new saw is capable of plunge cutting to fourteen inches and will cut a square opening with no over-cuts in material as thick as ten inches. The 613GC is powered by an 80cc, 5.7hp, 2-cycle gas engine, with an advanced air filtration system designed for wet-cutting aggregate materials

Features:

Long lasting "rim-style" drive sprocket
Reliability features built-in to eliminate minor breakdowns:
Air filter water seal system
High strength, electroplated chain tensioning screw
Pre-lubricated starter pawls
No kink water inlet hose
Uses Diamond Chains with SealPro^® O-Ring technology
Use the 613GC with standard "garden hose" water pressure. No need for a water booster pump.
5.7hp (80cc) engine designed specifically for wet cutting concrete in an abrasive environment
Special crankshaft sealing and air filtration
Sprocket side cover and guard flap designed for maximum operator safety
Easy access and simple maintenance requirements
Fixed-Position WallWalker^® helps ensure easier cuts in multiple positions

Free Freight On Any Bar and Chain Order
When Ordered with a Saw!

Bar & Chain Selection

12"	71395 Guide Bar	Use One Guide Bar For Every Three Chains - After two Chains flip Guide bar over	613GC
12"	Block & Concrete with #4 or 1/2" Rebar	71400 TwinMAX-29	613GC
12"	For Harder Materials such as Granite, Concrete Filled Block with #6 or 5/8" Rebar	71704 TwinMAX-29 Plus	613GC
12"	For Abrasive Materials - Block & Hollow Brick	71554 TwinMAX-29 Abrasive	613GC
14"	513122-14" Guide Bar	Use One Guide Bar For Every Three Chains - After two Chains flip Guide bar over	613GC
14"	Block & Concrete with #4 or 1/2" Rebar	71486 TwinMax - 32	613GC
14"	For Harder Materials such as Granite, Concrete Filled Block with #6 or 5/8" Rebar	71705 TwinMAX-32 Plus	613GC
14"	For Abrasive Materials - Block & Hollow Brick	71610 TwinMAX-32 Abrasive	613GC

Specifications
Engine Type	2-Stroke Single Cylinder Air-Cooled
Displacement	4.9 cu.inch (80cc)
Horsepower	5.7 HP (4.2kw) @ 9000 RPM
Engine Speed	12,000 ± 500 RPM Electronically governed 2800 - 3200 RPM idle
Chain Speed	5300 fpm (27 m/s), free running
Weight (with bar and chain)	21 lbs (9.5 kg)
Available Bar Lengths	Up to 14 inches (30cm)
Carburetor	Walbro, Throttle shaft sealed
Starter	Dust and water shielded
Ignition	Special water resistant electronic ignition
Clutch	Three-weight, single spring
Fuel Mix Ratio	25:1 gasoline-to-oil
Fuel Capacity	0.23 gal (.88 liter) 15-18 minutes run time per tank
Water Supply	Minimum 20 psi (1.5 bar)
Noise Level	100dB @ 1 meter
Vibration Level	10.5 meters/second
Cutting Rates
Hard aggregates & steel	15-25 sq-in/min (90-160 sq-cm/min)
Medium aggregates	20-30 sq-in/min (160-190 sq-cm/min)
Masonry, Soft aggregates	30-50 sq-in/min (190-320 sq-cm/min)

Datasheet Catalog

Download Free

ICS Frequently Asked Questions