 |
Brake Tooling
EDW1033, EDW1034,
EDW1034-65, EDW1035, EDW055-56, EDW065-56
Brackets, frames, pans
and tanks are just a few of the applications appropriate for brake
tooling. Available in 7", 8", 10" and 12" lengths (length varies by
machine), brake tooling includes a standard "punch" and a 4-way die
that allows for 1/16", 1/8", 3/16" and 1/4" material to be broke to
a 90 degree angle. The bottom brake die is held with brackets that
easily bolt to the mounting table. Precision, repeatable bending is
achievable with the combination of brake tooling and Edwards
electric stroke control option.
|
 |
Multi Shear
EDW1075
Cut solid rods,
squares, angle and bar-stock
with one tool!
The Multi Shear is perfect for the ornamental iron shop where
a clean cut is required on a variety of standard sized solid round
rod-stock and up to 13/16" square stock. The multi-shear also makes
quick work of small angle iron up to 2" x 2" x 1/4" and bar-stock up
to 1/4" x 6"
|
 |
Pedestal Die Table
EDW0895-00,
EDW0895-01
Working
structural steel?
The Pedestal Die Table is used as an alternative to the standard or
oversize die table and allows for the punching of 2" x 2" x 1/4"
steel angle, channel or beam sections. Section flanges and web
surfaces may be punched in standard or oversize format. Contact
Edwards for Pedestal Die Table sizing and fabrication applications.
|
 |
Coper Notcher
EDW1014,
EDW50-340-00, EDW1015, EDW1098
Need to trim a
little here, a little there?
Coper Notcher tooling, also known as a nibbler, allows for a small
nibble or a large sized bite to be taken out of plate, barstock or
angle (size varies by machine). This tooling is indispensable for
one-off or custom work where no two cuts are the same.
|
 |
Oversize Punch
EDW1024
When a standard punch is not
enough.
Commonly used in heavy industry, the Oversize Punch assembly
takes over where the standard assembly ends. The oversize
assembly includes oversize punch stem, nut, and oversize die
table which accommodates punch and dies from 1" to 1- 9/16"
round in 1/32" increments. Oversize punch and die sets (sold
separately) are available in standard rounds and custom shapes
and sizes. Contact Edwards for more information.
Punched holes or shapes larger than 1-9/16" require 241 Tooling
|
 |
241 Tooling
EDW1055
If you need a big hole, 241 is
your tooling solution.
241 Tooling accommodates punch and dies in standard rounds or custom
shapes from 1-9/16" through 4". We have seen 241 Tooling used to
punch access holes and slots in heavy, structural steel beams as
well as finished patterned holes in aluminum trailer frames for the
installation of LED lighting.
|
 |
Urethane Stripper
EDW1099
Keep your light-gauge material flat!
The Urethane Stripper accessory is designed to maintain the flatness
of material being punched by keeping constant pressure on light
gauge material through the punch and strip cycle.
|
 |
Pipe Notcher
EDW0925-00,
EDW1044, EDW1045, EDW1046, EDW1047, EDW1048, EDW1049
Build pipe railing, motorcycle or
car frames?
Pipe Notcher tooling eliminates the cutting and grinding required
for your saddle joint connections in schedule-40 pipe. Simply insert
your mild-steel or aluminum pipe into the bump-die housing, activate
the machine and cut a perfect saddle without any additional
finishing work. Available with dies to notch 1/2" to 2", the Pipe
Notcher will cut hours from your fabrication and assembly time.
Click here to
view a video clip of the Pip Notcher in action
|
 |
Magnetic Squaring Arm
EDW1016
Never do the same job twice?
The 2" x 12" Magnetic Squaring Arm will attach to any steel surface
with 40# pull strength per inch making this tool the most flexible
material guide available. Position the guide to the feed table and
slide your material against the heavy duty stainless steel casing
for perfect cuts every time. To release the magnet for
repositioning, simply rotate the threaded stud to break the magnetic
bond.
|
 |
Vee-Notcher
EDW0125-31
Similar to the
Coper Notcher in function but dedicated to the angle iron frame
industry, the Vee-Notcher tooling takes a precise 92 degree notch
from the bottom leg of angle up to 3" x 3" x 1/4" profiles. Once
cut, the uncut top leg profile is placed in brake tooling for a
precise 90 degree bend to create an angle iron frame. This tooling
is widely used in fabrication shops that create sub-frame assemblies
for other industries.
|
 |
Back Gauge
EDW1011
Fitted to the back of the Ironworker, the 48" back gauge accessory
provides an adjustable stop for the angle and bar shear stations of
your Edwards Ironworker. The sturdy construction and positive
attachment to the machine frame ensures accurate, repeatable cuts
for your production jobs.
|
 |
Gauging Table Kit
EDW0900-KIT
Need a helping hand?
Available in custom formats, the 3/8” x 12” x 16” punch Gauging
Table Kit takes the guess work out of making precise, repeatable
standard or oversized holes. The table bolts to late model standard
or oversize Pedestal Die Tables and includes one short and one long
movable guide fence. Movable guide fences clamp down to the table
surface with heavy duty hardware to direct your material to the
exact punch location every time. |
 |
Heavy Duty Gauging Table Kit
EDW0900-KIT-HD
Need a heavy duty helping hand?
Available in oversize, the 1” x 12” x 16” punch Heavy
Duty Gauging table accessory takes the guess work out of making
precise, repeatable standard or oversize holes. Movable guide fences
clamp down to the table surface with heavy duty hardware to direct
your material to the exact punch location every time. Kit includes
heavy duty table, mounting plate, hardware and one short and one
long movable guide fence. |
 |
Fabricator’s Protractor
EDW1017
A useful tool for any fabricator, the heavy duty Fabricator’s
Protractor guides your work to the shear or punch stations
through 180 degrees. Gauged at 15 degree increments with an
additional designation of 22.5 degrees, the protractor features
a long leg, reversible design to accommodate both right and left
hand operators.
|
