|
Super Special -
Limited Time Offer! Prices So Low we can't show them
online.
Call Today Toll Free @ 1-800-458-3687.
Don't
Forget: ASK about our Super Specials on replacement chains when buying your ICS Saw.
The 613GC from ICS cuts twice the depth of an ordinary circular blade
cut-off saw.
Weighing only 21 pounds complete, this new saw is capable of plunge
cutting to fourteen inches and will cut a square opening with no over-cuts
in material as thick as ten inches. The 613GC is powered by an 80cc, 5.7hp, 2-cycle gas engine, with an
advanced air filtration system designed for wet-cutting aggregate
materials |
Features:
-
Long lasting "rim-style" drive sprocket
-
Reliability features built-in to eliminate minor breakdowns:
-
Air filter water seal system
-
High strength, electroplated chain tensioning screw
-
Pre-lubricated starter pawls
-
No kink water inlet hose
-
Uses Diamond Chains with SealPro®
O-Ring technology
-
Use the 613GC with standard "garden hose" water
pressure. No need for a water booster pump.
-
5.7hp (80cc) engine designed specifically for wet cutting
concrete in an abrasive environment
-
Special crankshaft sealing and air filtration
-
Sprocket side cover and guard flap designed for maximum
operator safety
-
Easy access and simple maintenance requirements
-
Fixed-Position WallWalker®
helps ensure easier cuts in multiple positions
|
Specifications |
| Engine Type |
2-Stroke Single Cylinder Air-Cooled |
| Displacement |
4.9 cu.inch (80cc) |
| Horsepower |
5.7 HP (4.2kw) @ 9000 RPM |
| Engine Speed |
12,000 ± 500 RPM
Electronically governed
2800 - 3200 RPM idle |
| Chain Speed |
5300 fpm (27 m/s), free running |
| Weight (with bar and chain) |
21 lbs (9.5 kg) |
| Available Bar Lengths |
Up to 14 inches (30cm) |
| Carburetor |
Walbro, Throttle shaft sealed |
| Starter |
Dust and water shielded |
| Ignition |
Special water resistant electronic ignition |
| Clutch |
Three-weight, single spring |
| Fuel Mix Ratio |
25:1 gasoline-to-oil |
| Fuel Capacity |
0.23 gal (.88 liter)
15-18 minutes run time per tank |
| Water Supply |
Minimum 20 psi (1.5 bar) |
| Noise Level |
100dB @ 1 meter |
| Vibration Level |
10.5 meters/second |
| Cutting Rates |
| Hard aggregates & steel |
15-25 sq-in/min
(90-160 sq-cm/min) |
| Medium aggregates |
20-30 sq-in/min
(160-190 sq-cm/min) |
| Masonry, Soft aggregates |
30-50 sq-in/min
(190-320 sq-cm/min) |
Free Freight On
Any Bar and Chain Order When Ordered with a Saw!
|
Bar & Chain Selection
 |
|
12"
|
71395 Guide Bar |
Use One Guide Bar For Every Three Chains -
After two Chains flip Guide bar over |
613GC
|
|
12" |
Block & Concrete with #4 or 1/2" Rebar |
71400 TwinMAX-29 |
613GC |
|
12"
|
For Harder Materials such as Granite,
Concrete Filled Block with #6 or 5/8" Rebar |
71704 TwinMAX-29 Plus
|
613GC
|
|
12"
|
For Abrasive Materials - Block & Hollow
Brick |
71554 TwinMAX-29 Abrasive
|
613GC |
|
14" |
513122-14" Guide Bar |
Use One Guide Bar For Every Three
Chains - After two Chains flip Guide bar over |
613GC |
|
14" |
Block & Concrete with #4 or 1/2" Rebar |
71486 TwinMax - 32 |
613GC |
|
14" |
For Harder Materials such as Granite,
Concrete Filled Block with #6 or 5/8" Rebar |
71705 TwinMAX-32 Plus |
613GC |
|
14" |
For Abrasive Materials - Block & Hollow
Brick |
71610 TwinMAX-32 Abrasive |
613GC |
|
ICS Frequently Asked Questions
Super Special -
Limited Time Offer! Prices So Low we can't show them
online.
Call Today Toll Free @ 1-800-458-3687.
Don't
Forget: ASK about our Super Specials on replacement chains when buying your ICS Saw. |
