Technical Sales 1–800–458–3687

General Equipment EP8HL Hazardous Locati

EP8HL HAZARDOUS LOCATION AIR VENTILATION BLOWER

EP8HL HAZARDOUS LOCATION AIR VENTILATION BLOWER

 

EP8HL VelociMax SERIES HAZARDOUS VENTILATION BLOWER
MODEL DESCRIPTION WEIGHT (LBS)
EP8HL Blower, radial, .33 HP, 115 VAC, 60 HZ, single phase, explosion-proof, fully enclosed, non-vented (TENV) electric motor, lever activated internal ON/OFF motor switch, 1725 RPM, 8 inch diameter inlet and outlet. 73.0
EP8HL VelociMax SERIES  DUCTING and STORAGE
PART NUMBER DESCRIPTION WEIGHT (LBS) COMPATIBLE PRODUCT
SCFD825 Ducting, anti-static, 8 inch diameter, 25 foot length, wire helix reinforcement w/anti-scu strip. Includes aluminum attachment cu , static ground leads, opposite end nylon ring.

15.0

EP8HL

SCHL8 Storage canister, aluminum, welded, heavy-duty w/cover. Includes carry handle and cover latch. For use with SCFD825 ducting. 7.5

 

 

HAZARDOUS LOCATIONS

Model EP8HL is CSA certified for use where the possibility of a hazardous environment exists as defined by the National Electric Code® including: Class I, Group D; Class II, Group G or Class III atmospheres. AC electric motor power source. Special, statically-conductive ducts and separate storage accessories are designed for specific use hazardous locations.

EP8HL HAZARDOUS LOCATION AIR VENTILATION BLOWER

8 inch inlet and outlet diameter. Certified by Canadian Standards Association (CSA) for use in National Electric Code Class I Group D, Class II Group G and Class III hazardous location atmospheres and non hazardous atmospheres. Less statically conductive duct.

  • Power Source: 1/3 HP, 115 VAC, 1 phase, explosion-proof motor
  • Fan Type: Centrifugal
  • Construction: Spark proff
  • Duct Diameter: 8 inches, statically conductive w/ground
  • Free Air Flow: 1277.4 CFM

Download (PDF) Files

EP8HL Hazardous Location Reasons

EP8HL Hazardous Location Blower Literature

EP8HL Hazardous Electric Blower Operator Manual

EP8HL Hazardous Location Blower Parts

EP8HL HAZARDOUS LOCATION AIR VENTILATION BLOWER

8 inch inlet and outlet diameter. Certified by Canadian Standards Association (CSA) for use in National Electric Code Class I Group D, Class II Group G and Class III hazardous location atmospheres and non hazardous atmospheres. Less statically conductive duct.

 

Specifications:


POWER SOURCE
Type: 1/3 HP (23kw), 1725 RPM, 60Hz, 115 Volts, AC, Single Phase
Speed Control: Single Speed

BLOWER
Type: Radial
Material: Cast aluminum
Wheel Type: Steel
Size: 8 inch (203 mm) Nonumal Diam. inlet.Outlet

GENERAL
Mounting: Rubber
Type: Anti-Virbration
Weight: 53 lbs (24 kg) Rower Cord Type: Flexible Tpye, 14-3 AWG
Power Cord Connection: Male, NEMA 5-20P Configuration

DIMENSIONS
Height: 19-3/8 inch (492 mm) Length: 21 inch (533 mm) Width: 15-1/2 inch (394 mm)

FLOW RATES
Free Air: 1277.4 CFM (35.7 m3/min)
One 90 Degree Bend: 738 CFM (20.7 m3/min)
Two: 90 Degree Bends: 578.8 CFM (16.2 m3/min)

Collapsible Ducts


 
Part No.
Description
scfd815 Statically conductive collapsible duct,

Statically conductive collapsible duct, 8 inch diameter x 25 foot length, wire helix reinforcement with anti-scuff strip. Complete with aluminum attachment cuff, static ground leads and nylon ring on opposite ends. For use with the EP8HL Blower only.


   

 

LIMITED PRODUCT WARRANTY


GENERAL EQUIPMENT COMPANY makes the following limited warranty to the original purchaser of each new and unused light construction equipment product:

GENERAL EQUIPMENT COMPANY MAKES NO WARRANTY THAT THE LIGHT CONSTRUCTION PRODUCTS SOLD HEREUNDER SHALL BE MERCHANTABLE OR THAT SUCH PRODUCTS SHALL BE FIT FOR ANY PARTICULAR PURPOSE AND THERE ARE NO WARRANTIES EXPRESSED OR IMPLIED MADE OTHER THAN ITS STANDARD, LIMITED WARRANTY.

WHAT THE LIMITED WARRANTY COVERS

GENERAL EQUIPMENT COMPANY warrants that each new and unused light construction equipment product and or accessory product sold by it: A) to be free from defects in material and workmanship under normal use/service for a period of two (2) years from date of purchase: B) to warrant the labor expenses associated with defects in material and workmanship for a period of one (1) year from date of purchase. The obligation under this warranty being limited to current flat labor rates and the replacement and/or repair at its Owatonna, Minnesota, factory site, or at an authorized dealer designated by it, of such part or parts as shall appear upon inspection to have been defective in material or workmanship at the time sold, provided that the part or parts claimed defective are returned to the inspection point, transportation charges prepaid. At the time of requesting warranty service, the purchaser must present evidence of the purchase date of the part or parts submitted for warranty inspection.

The only remedies the purchaser has in connection with the breach of performance of any warranty for the light construction equipment products sold by GENERAL EQUIPMENT COMPANY are those set forth in this document. In no event will GENERAL EQUIPMENT COMPANY, its authorized dealer or representative, or any company affiliated with GENERAL EQUIPMENT COMPANY be held liable for any incidental or consequential damages or injuries.

WHAT THE LIMITED WARRANTY DOES NOT COVER

This warranty does not cover depreciation or damage caused by: normal wear, accident, improper protection in storage, improper use, alterations, tampering, the environment, improper maintenance, lack of maintenance or incidental costs incurred by the original purchaser while the light construction equipment product is being examined and or repaired under warranty. In addition to the above limitations and/or exclusions, the following basic product components are not covered by the limited warranty:

1) Parts and/or components subject to wear with normal usage, but not specifically limited to the following:

a) High impact/wear related components including, but not limited to: V-belts, flails, flail rods and flail drums.
b) High abrasion/wear related components including, but not limited to: augers, auger flighting and boring heads.
c) Engine throttle control cable assembly and related control devices.
d) Centrifugal clutch components including, but not limited to: shoes, springs, drum and motor assembly.

2) Parts and labor for scheduled and general maintenance services as defined in the applicable Operators Manual.

3) Engines, motors, controls and other accessories sold with, attached to, or operated with a light construction equipment product sold by GENERAL EQUIPMENT COMPANY and warranted separately by the Original Equipment Manufacturer (OEM) per its respective warranty program. Contact the Customer Service Department of GENERAL EQUIPMENT COMPANY for assistance in obtaining specific OEM warranty coverage.

This limited warranty gives you specific legal rights and may also have other rights which may vary from state to state. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. These limitations may not apply to the original purchaser.

EP8HL
BLOWER, HAZ, .33HP, 115VAC, 8D
Mfg. item #: EP8HL
GENEP8HL
Call for freight quote on this item or we will confirm freight charges before shipping.1
$2,136.50

176
SCFD825
DUCT, CONDUCTIVE, 8D, 25L
Mfg. item #: SCFD825
GENSCFD825
Call for freight quote on this item or we will confirm freight charges before shipping.1
$501.15

176
SCHL8
CANISTER, AL, 8D
Mfg. item #: SCHL8
GENSCHL8
Call for freight quote on this item or we will confirm freight charges before shipping.1
$308.55

176
Copyright © 2024 Smith-Hamilton, Inc
0.004 240308 10:51