Technical Sales 1–800–458–3687

Hud-Son CH 170 OEM HF/HD Wood Chipper

CH160 OEM HF/HD

EASY TO OPERATE * POWERFUL CHIP DISCHARGE
*  EASILY SERVICED
 * INTERCHANGEABLE FEED CHUTES

The Valby CH 160 OEM HF/HD is a chipper unit which can be mounted stationary or on a trailer.  The chipper has a self-contained hydraulic system which powers the power feed.  The hydraulic system becomes active as soon as the chipper starts turning.

Chipper is powered from engines or electric motors.

The chipper has a 8" diameter V-belt pulley with grooves for "A" type belts.  The chipper can be turned 540 to 1500 rpm.  At 540 rpm, the chipper requires 30 HP to chip 6" diameter material.  The power requirement increses when the chipper is turned faster.

The chipper is driven from a 8" diameter V-belt pulley (behind the sprocket).   The chipper has an oiltank, filter and a relief valve.  The chain drives the aluminum oil pump.

The power feed is useful when whole trees with branches are chipped.  The hydraulic feed is controlled from a control bar which runs on top of the feed chute.   The operator can select feed, stop and reverse from the control bar.

The large 10 1/8" diameter top feed roller will climb on top of the material and drag it in.  The roller is spring loaded and it pushes the material together so that it will fit through the feed chute.

Ease of Operation
Because of the low feeding point, material does not have to be lifted high, which assures easier feeding of the chipper.

Saftey Features
The Valby chippers do not have any knife motion toward the operator.  This reduces the risk of material flying back through the feed chute.  The discharge height is 86" above ground so the discharge is above eye level.  The accomplish safe operation in various wind directions, the Valby chipper's discharge direction is adjustable 360 degrees.  The chipper feeds the material smoothly and does not jerk it from the operator's hands.

Powerful Chip Discharge
The fan is built into the chipper's disk so it also retains its rotational speed under heavy loads.  The chips can be directed in any desired direction as the discharge chute rotates 360 degrees.  The chips can be placed near or far by aiming the deflector bonnet.

Ease of Service
The knives can be sharpened about 50 times before replacement.  The changing of the knives takes only 10 minutes.  The knives are easy to get to and no special tools are needed for the change.  The upper housing opens up for easy access to the knives.  The discharge chute is easy to remove so the chipper can be stored inside low buildings.

Specifications
The Valby CH160 OEM HF/HD chipper produces uniform chips wich can be used for burning, animal bedding, landscaping and mulch.  The chipper is capable of chipping 6 1/4" diameter round wood.  It can handle residue from logging, land clearing, orchards and gardens.  The chipper can also handle slabs up to 9" wide.   The material is drawn ito the chipper at the speed of 1 to 3 feet per second.   The chipper is self-feeding and draws in the material without pushing by the operator.

TECHNICAL DATA ON CH 160 OEM HF/HD CHIPPER

Power Range: 17-50 HP
Rotator Speed: 540-1500 RPM
Chipping Rotor:
Diameter: 2 3/8"
Weight: 220 LBS
Knives: Two 8 3/4" x 3 7/8" full-size knives
Bearings: Spherical Roller
Rotation Speed: 540-1500 RPM
Infeed Capacity: 6 1/4" diameter round wood
Adjustable vertical anvil;
Adjustable horizontal anvil;
Mean Chip Length: 9/16"
Feed Height: 19" above ground
Discharge: Adjustable 360 degrees Height:   86"
Production: 8-30 cu yards/hr. 1-8 tons/hr.
Hydraulic Power Feed HF 160:
Powerfeed roller size: 10 1/8" diam, 10 3/8" wide
Hydrualic motor size: 24 cu inches
Weights: Chipper with HF 160 powerfeed: 1100 lbs.
Model Description Weight
Ch160 OEM-F 6" Woodchipper with 8" pulley for
"A" Section Belts
710 lb
CH160 OEM HF/HD 6" woodchipper with 8" pulley; internal hydraulic pump, hydraulic power feed 1050 lb
There are no further details.
There are no further specifications.
There is no further information.
There are no listed accessories.
CH160OEM/F
Mfg. item #: CH160OEM/F
HUDCH160OEM/F
lease to own for as little as:$140 per month!
Call for freight quote on this item or we will confirm freight charges before shipping.1
$6,990.00

5515
CH150OEM/HF/HD
HF/HD}1050 lbs Valby Wood Chippers
Mfg. item #: CH150OEM/HF/HD
HUDCH150OEM/{00
lease to own for as little as:$228 per month!
Call for freight quote on this item or we will confirm freight charges before shipping.1
$11,400.00

5515
Copyright © 2024 Smith-Hamilton, Inc
0.004 150419 18:39