Imer Mighty Small 50 Grout Pump, Sprayer and Mixer
The Mighty SMALL 50 can operate continuously on 110v 20 amp service. This machine has the ability to spray or pump up to 3.5 gallons of material per minute through 85 ft. of 1 inch hose. The versatility of the Mighty SMALL 50 is very impressive - spray fire proofing, pump grout into door jams, fill moulds at precast plants, spray stucco onto residential homes, apply grout to finish rock walls. Easy to use, easy to clean, it's a money making machine!
Standard Equipment - Supplied with each Mighty Small 50
The Small 50 is priced as the pump only. This is because you do not always need an application gun kit. If you are just pumping you do not need a gun kit or the compressor. We also sell the hose separately as different jobs require different lengths of hose.
This pump/sprayer runs on 110 volts with inverter technology which incorporates a digital panel and frequency control that raises or lowers the screw rpm. The inverter on this spray and grout pump gives 220 volt performance at the convenience of plug-in-anywhere 110 volt. A rheostat controls the motor RPM which means that you have total control of the flow to match with the material being applied.
All of the operation on this Small 50 Spray and Grout Pump is controlled by the panel which can detect the wrong voltage and shut down as a safety. The unit will sense a jamb and cut the power to the pump. An error message followed by a number will display to help you with the troubleshooting. Thermal overloads are in place on the 100pct duty cycle motor. This means that the motor on this Imer unit can run all day, every day. The control panel will sense an overload before the thermal protection on the motor. This is just the level of how safe, secure and sophisticated this machine is. The Small 50 Spray and Grout Pump boasts very big performance numbers which are 3.5 gallons (1/2 CF) per minute on pumping and 60 square yards at 1/2 inch thick of spraying power with 60pct utilization. (100 square yards at 100pct). Features:
|Hopper Capacity||12.5 gal|
|Motor Rating||1 3/4 hp, 110v, 18 amps|
|Stator Screw rpm||variable rheostat control 8-140 rpm|
|Material Flow Rate||2 to 3.5 gal per minute|
|Max. Pumping Distance||3/4" hose - 50 ft / 1" hose 85 ft|
|Operating Dimensions (boxed)|
Dual Diaphragm V-Stroke Compressor Model #1107546
Note: The compressor must be purchased if you want to both pump and spray material. The compressor iis a continuous duty, all aluminum, twin diaphragm, low pressure, high volume 110 volt unit. Its light, strong, and reliable! This compressor is also set-up and calibrated to operate as per the instructions of the Mighty Small 50 computer. It is also maintenance free, as it does not require an oil reservoir feed system.
Vibrating Screen Model# 1107548
Note: The vibrating screen prevents unmixed materials from entering into the hopper. It also catches all debris which is 5/16 inch or more in size. (Small stones etc.)
To apply materials, you must have an application kit. This kit will include the hoses, the application gun, and various pattern caps and nozzles for the end of the application gun.
Premixed mortar / Fireproofing Kit
Used for spraying rough coats where material needs to be built-up such as fireproofing, cement based stucco, gypsum based products, etc.
Model # 1107005
Gun Only, includes 1 tip Model # 1107540
Stucco, and fine coatings gun kit Use for paints, elastomeric coatings, acrylic stuccos, cement based waterproofing (less than 1/8 inch of coverage).
Fine Coat Gun with tips Model L000051
High-Pressure Grout Kit
Adjustable pressure regulator allows for a psi fill pressure of 0 to 65 psi. Works well to allow for filling/injecting into structures which require a specific psi, such as historical preservation projects.
5 Foot Overhead Wand - Sprays overhead or into hard to reach spaces, includes 1 qty. 14mm fireproofing tip
Allows the pump hose to be hung in place while hollow cavities are filled with material
Material and Air Hose
Tuck Pointing Gun Kit w/ Automatic on/off
This pistol style tuck pointing gun connects electronically to the Small 50 Pump and stops and starts as you release or close the pistol lever. Tuck point with control and speed.
Standard Green Stator/Rotor
Standard stator/rotor is good for up to 3.5 gallons a minute and 300 PSI.
Stator Model 1107030
Rotor Model 1107031
Accessory Yellow Stator/Rotor
Accessory stator rotor is good for up to 1.5 gallons a minute and 400 psi, use when slower flow or higher pressure is required.
Stator Model 1107032
Rotor Model 1107033
|Models and Accessories|
|1106045||Mighty Small 50 Portable 110v Pumping and Spraying Machine|
|1107546||DUAL DIAPHRAGM V-STROKE COMPRESSOR|
|1107005||PREMIXED MORTAR/FIREPROOFING KIT|
|1107010||STUCCO/FINE COATINGS GUN KIT|
|1107006||HIGH-PRESSURE GROUT KIT|
|1107549||5' OVERHEAD WAND|
|1107525||50ft 1in MATERIAL HOSE W/ CAM COUPLING|
|1107526||33ft 1in HOSE W/CAM COUPLING|
|1107527||16ft 1in HOSE W/CAM COUPLING|
|1107532||50ft 1/2in AIR HOSE W/ CHICAGO FITTINGS|
|1107531||33ft 1/2in AIR HOSE W/CHICAGO FITTINGS|
|1107505||TUCK POINTING GUN KIT W/AUTO ON/OFF|
|1107030||STANDARD GREEN STATOR|
|1107031||STANDARD GREEN ROTOR|
|1107032||ACCESSORY YELLOW STATOR|
|1107033||ACCESSORY YELLOW ROTOR|
|1107011||STUCCO/FINE COATING GUN ONLY|
|1107540||PREMIXED MORTAR/FIREPROOFING GUN ONLY|