Due to limited stock from the factory,
please call for avalability of Comet 2 lathe model 46300
![]() |
![]() |
![]() |
The recomended Chuck for this lathe is a Teknatool Nova G3 Reversable Chuck Click the image above for more infomation |
Dont forget your turning tools Check out or full line of easy wood tools |
Download brochure (.pdf)
Portable, space saving yet delivers the capacity and the rugged stability of larger lathes. With the NOVAs unique VERSATURN Accessories, transform your NOVA Comet II midi lathe into a all-in-one Wood Turning and Wood Working system. The NOVA Comet II Midi Lathe is perfect for a wide range of Wood Working projects.
Standard Equipment:
Comet II Midi Lathe Features and Benefits:
Powerful Electronic Variable Speed Motor offers an RPM range from 250 to 4000 RPM With a super lower speed up to a super-high speed, this makes the NOVA Comet II
Midi Lathe the perfect choice for a variety of projects, from pens to bowls.
Forward and Reversing Switch offers addtional flexiblity and allows you to achieve a superior finish.
12 inch Swing Capacity over bed and 16.5 inch between centers, extendable with bed extension accessory.
3 Step Pulley System offers different speed ranges while providing maximum flexbility. The middle step usually provides enough range for most Wood Turning
applications, however the addtional 2 steps provide more torque for the more demanding applications.
Versaturn Adapatable Technology Accessories
The NOVA Verstaturn Adaptable Technology is exclusive to NOVA. With the addition of the Versaturn Coupler, these accessories enable you to turn your NOVA Comet II Midi Lathe into a:
(Each accessory is sold seperately, these cannot be fitted to any other lathe other than the NOVA Comet II)
Plus these Additional Features ( standard on all NOVA Lathes):
Plus these Additional Features ( standard on all NOVA Lathes):
Product Technical Specification:
![]() |
![]() |
![]() |
Versaturn Coupler |
Versaturn Grinding Wheel SKU 47002 6 inch Whitestone Wheel, with the Comets variable speed adjustment up to 4000rpm which enables you to select just the right speed to grind, without burning the tool edge. Requires the coupler to use on the Comet II Lathe |
Versaturn Wire Brush SKU 47004 6 inch Soft Wire Brush, many uses from cleaning steel and metals to polishing. Good for some use in abrading soft stone and wood for special effect finishes. Requires the coupler to use on the Comet II lathe. |
Comet with optional bed accessory added
Controller detail - note switch types may vary from country to country and may differ to that shown
The belt position is easy to change and the 3 step pulley system provides a wide range of speeds while providing maximum flexibility
Additional Accessories:
Models and Accessories | |
---|---|
46300 | Comet II Bench Lathe |
47050 | Comet II Stand |
47001 | Comet II Bed Extension |
47002 | Comet II Versaturn Grinding Wheel Kit |
47004 | Comet II Versaturn Wire Brush |
47000 | Comet II Versaturn Coupler |
6002 | Faceplate Ring 130mm |
6001 | Faceplate Ring 100mm |
6000 | Faceplate Ring 50mm |
2MTLC | 2 MT Simple Live Center |
2MTSPUR | 2 MT Spur Center |
2MTNA | Acruline 2 MT Alignment System |
5015 | Nova Live Center System |
Woodworking Lathe Chucks, Tools & Duplicators | ||
---|---|---|
![]() |
![]() |
![]() |
TeknaTool Nova Precision Lathe Chuck,Jaws & Inserts |
Easy Lathe Tools & Chucks | VEGA Midi Lathe Duplicator |
NOVA G3 COMET II REVERSIBLE CHUCK
The Nova G3 Reversible chuck is the next generation smaller geared chuck, with a unique reversible lock function/feature designed exclusively for the NOVA Comet II Midi Lathe. Provides high power geared chuck option suited for the smaller capacity of the NOVA Comet II Midi Lathe.
Its light weight, and with less overhang which is perfect for smaller lathe spindles. The small 1.79 inch body length delivers less overhang from the spindle than the larger geared Chucks - the SuperNova2 Chuck and the Nova Titan Chuck, reducing stress on smaller lathe spindles. Note: If you don't have a NOVA Comet II Midi Lathe you cannot use this chuck. Please instead purchase the standard G3 Chuck. If your lathe is less than 14 inch diameter swing, please have a look at the Nova Precision Midi chuck. If your lathe has more than 14 inch diameter swing, please have a look at the SuperNova2 Chuck or the NOVA Titan Chuck.
|
![]() |
Features standard on all NOVA chucks:
Additional G3 Features and Benefits
|
|
Product Technical Specification
|
|
Compatibility Capable to take entire NOVA Jaws range. (recommend smaller jaws only to fit the capacity range of the smaller chuck) Only NOVA Chucks give you the same jaw fixing system and same insert/adaptor system across all chuck models. This means all accessory jaws in the range fit all the chucks in the range, including older chuck models, giving you the ultimate flexibility. In buying a NOVA chuck, you can be confident that whether you want to move up or down the range, any accessories you have invested in will Fit. May also be used on the Delta 46-461 wood lathe |
|
Standard Equipment
|
Threads Covered:
|
Teknatool Wood Turning Lathe Chucks | |
48232 | G3 Chuck Reversible 1" 8 TPI |
Easy Rougher - The Next Step in Woodturning
The Easy Rougher is a carbide cutter woodturning tool that addresses
fatigue, safety, and efficiency like no other type of tool on the market. Designed to be kept flat on the tool rest and level to the floor, the Easy Rougher will effortlessly hog away massive
amounts of material for any woodturning process without the need for sharpening. The tool design provides support directly beneath the cutting edge transferring the cutting pressure downward
allowing the lathe to take the pounding that you would normally suffer through when using a conventional bowl gouge for roughing. No more white knuckling a bowl gouge.
Easy Finisher - Yet Another Innovation in Woodturning
With another step forward in woodturning innovation, Easy Wood Tools now
offers you a tool to take up where the Easy Rougher leaves off. The Easy Finisher has a round carbide cutter perfect for doing the inside work on smaller bowls and for larger coves on spindle work.
Our carbide inserts are made in the USA and we are pleased to offer you a tool that is 100 percent made in America.
If you own one of our existing Easy Roughers, you well know by now that we deliver even more than we advertise, as hard as is was for you to believe before your first purchase. I assure you the
productivity of this tool will exceed your highest expectations. You just can not predict the possibilities or joy this tool will provide you. In testing the prototypes for this new design, I found
myself creating forms that were never even on my list to try because the dangers and complications of existing tools were just not worth the trouble. Craig Jackson, Founder
Like the other Easy tools, the Easy Finishers are designed to be used with the tool rest set so that when the tool is held level the top of the cutter is on center. Then just keep it level to the
floor and flat on the tool rest for all types of cuts... it does not get any easier than that. There are no complicated approach angles, or bevels to ride. The design of this tool allows the Easy
Finisher to effortlessly cut from the center of a bowl out to the rim OR from the rim to the center! All without changing any angles whatsoever. You just stand in one spot and cut coming and going
until you get to the shape you want.
The Easy Finisher utilizes the same carbide cutter technology as the Easy Rougher that reduces strain and fatigue, improves productivity, and virtually eliminates sharpening. It comes loaded with
one round cutter and when it gets dull, you just rotate the cutter for a fresh cut. Please note: The round cutters are
not interchangeable with the carbide cutters on the Easy Rougher tool
bars.
When the cutter eventually gets dull, just loosen the retaining screw and rotate cutter about 1/4 of a turn, then re-tighten the screw.
We promise this tool will open up a whole new level of design possibilities for your craft and it will exceed your expectations. If not, return for a complete refund.
Replacement carbide cutter number is engraved right on the tool bar.
Available in four sizes - Mini, Mid-Size, Full-Size and Pro. See purchase page for all products, sizes and accessories.
Easy Rougher - The Next Step in Woodturning
The Easy Detailer tools really pick up where other tools leave off and
provide another level of woodturning creativity as the unique diamond cutter shape fits in tight places where the cutters on the other tools will just not fit.
These tools were designed for the primary purpose of doing the small intricate work and cutting final details on your projects such as small coves and beads on both spindle and bowl work. They are
also very handy for cutting chuck tenons and making inside reverse angle cuts for inside chucking bowls with dovetail jaws. You may find they work well for hogging your green wood projects
too.
The Easy Detailers are engineered to cut going straight in employing just the nose of the tool.
The Easy Detailer tools are engineered with a reduced relief angle to the long cuttings edges making the long edges less aggressive when held in contact with the wood as the nose of the tool is
cutting. In use, the long edge is intended to perform as a "control surface" and serve to be in contact with the wood just behind the cut; much like a bevel is being rubbed.
For safety reasons, avoid plunging the tool so deep into the work at once to the depth you would have both sides of the cutter in contact with the wood too greatly at the same time. This could
cause too much force at once and lead to binding of the tool in the groove.
Each diamond-shaped Easy Detailer cutter is engineered to fit all size Detailer tools in our current product line. When the cutter eventually dulls, just loosen the retaining screw and rotate
cutter, then re-tighten the screw.
Replacement carbide cutter number is engraved right on the tool bar.
Available in four sizes - see purchase page for all products, sizes and accessories.
PART NUMBER | DESCRIPTION |
---|---|
2200 | MID-SIZE EASY ROUGHER |
3200 | PRO EASY ROUGHER |
6300 | MID-SIZE EASY FINISHER |
3400 | PRO EASY FINISHER |
7300 | MID-SIZE EASY DETAILER |
3700 | PRO EASY DETAILER |
Due to limited stock from the factory,
please call for avalability of Comet 2 lathe model 46300