Electric Motors
Oztec Electric motors are manufactured to exacting specifications to withstand the rough day to day abuses associated with construction sites. Lightweight, compact
and fitted with our comfortable adjustable shoulder strap, this one man power unit will speed through the stiffest concrete. Using the Vibrator Selection Chart allows you to combine power units
with any of Oztec's steel or rubber vibrator heads for maximum productivity.
All Oztec Power Units (gas and electric) run vibrator heads 11,000 to 12,000 vpm. They never drop below 10,000vpm even in the lowest slump concrete (near 0) when
maximum head size specifications are followed.
Oztec power units come standard with the Quick Disconnect "QD" system. Changing shafts and heads on the job is a snap.
Job Site Proven
Tough, Rugged, and Durable! Oztec's design has been extensively tested and used on-the-job for over thirty years. The wrap around protective frame and shock absorbers effectively protect Oztec
motors from damage even when dropped or thrown from heights of over six feet.
Oztec units meet all United States OSHA and Canadian safety standards.
|
OZTEC Electric Vibrator Motors
|
 1.2OZ
|
115V-50/60Hz,1 Phase AC/DC,9 AMPS
|
|
1.8OZ
|
115V-50/60Hz,1 Phase AC/DC,15 AMPS
|
|
2.4OZ
|
115V-50/60Hz,1 Phase AC/DC,17 AMPS
|
|
3.2OZ
|
115V-50/60Hz,1 Phase AC/DC,19 AMPS
|
Gas Power Units
It must say "OZTEC" to be the industry's best concrete vibrator...
Powerful, portable and reliable, Oztec gas power units provide ultimate and immediate adaptability on the job. Utilizing rugged and dependable Honda gasoline engines,
coupled to our "speed-up" transmission, vibrator heads develop 12,000 vpm and never drop below 10,000vpm. Even in the heaviest low slump concrete loads. (Tested in near 0 slump concrete). This
10,000 - 12,000vpm range is essential for high-quality concrete.
(Direct drive units "scream", have short lives and usually drop below 10,000vpm when the head is immersed in concrete).
Two powerful Backpack Models:
Mounted on very comfortable frames, OZTEC backpacks BP-35 and BP-50a allow operators incredible maneuverability around the job. Run time with full tank approximately 1 hour plus.
All Oztec power units come standard with the Quick Disconnect "QD" system.
Note:Shaft must be all-the-way-in before releasing lever.
|
OZTEC Backpack & Portable Vibrator Power Units
|
|
BP-35
|
BP-35 1.75hp Honda Gas 15lbs
|
|
BP-50A
|
BP-50a 2.5hp Honda Gas 25lbs
|
|
GV-5H
|
5HP B & S Gas Portable Vibrator w/Wheels
|
|
GV-5WH
|
5HP HONDA Gas Portable Vibrator w/Wheels
|
Oztec Vibrator Steel Head produce the highest amplitude and centrifugal force, generating the largest radius of influence of any heads available. Energy is efficiently transferred from the motor,
via the shaft, to the head, which is all eccentric (vibrating the entire head). Whether combined with one of Oztec's electric or gasoline powered motors and choice of flexible shaftsââ¬Â¦The results
are exceptional!
Superior consolidation, increased productivity and a process more forgiving of less than perfect vibrating techniques.
The Benefits?? Lower costââ¬Â¦Higher earningsââ¬Â¦Superior quality concrete!!
Not sure what parts you need to make a complete system?
Oztec Vibrator Heads produce the highest amplitude and centrifugal force, generating the largest radius of influence of any heads available. Energy is efficiently
transferred from the motor, via the shaft, to the head, which is all eccentric (vibrating the entire head). Whether combined with one of Oztec's electric or gasoline powered motors and choice of
flexible shaft, the results are exceptional! Superior consolidation, increased productivity and a process more forgiving of less than perfect vibrating techniques. The benefits? Lower cost, Higher
earnings, Superior quality concrete!
Radius of Action - The most important bit of information needed for complete consolidation.
Radius of Action is the distance from the center of the vibrator to the outer edge, where complete consolidation takes place (see diagram).
For quality concrete Oztec lists conservative values for "Radius of Action". Complete consolidation is necessary for low slump concrete with close meshed reinforcement bars, high strength concrete
and architectural concrete.
Radius of Action can be twice the listed values when slump is high or super plastisizers are used. It is important these values are used only as a general guide. Specifications are subject to
change.
|
OZTEC Vibtror Heads
|
|
OZTEC Standard Steel Vibrator Heads
|
|
HP075OZ
|
3/4" Steel Heads (Penclie Head)
|
|
H100OZ
|
1" Steel Heads
|
|
H125OZ
|
1-1/4" Steel Heads
|
|
H150OZ
|
1-1/2" Steel Heads
|
|
H175OZ
|
1-3/4" Steel Heads
|
|
H200OZ
|
2" Steel Heads
|
|
H250OZ
|
2-1/2" Steel Heads
|
|
OZTEC Rubber Coated Vibrator Heads
|
|
HR188OZ
|
1-7/8" Rubber Heads
|
|
HR250OZ
|
2-1/2" Rubber Heads
|
|
HR275OZ
|
2-3/4" Rubber Heads
|
|
HSR275OZ
|
2-3/4" X 6" Rubber Heads
|
|
OZTEC Rubber Tip Vibrator Heads
|
|
H100OZ-RT
|
1" Rubber Tip Heads
|
|
H125OZ-RT
|
1-1/4" Rubber Tip Heads
|
|
H150OZ-RT
|
1-1/2" Rubber Tip Heads
|
|
H175OZ-RT
|
1-3/4" Rubber Tip Heads
|
|
H200OZ-RT
|
2" Rubber Tip Heads
|
|
H250OZ-RT
|
2-1/2" Rubber Tip Heads
|
Oztec Standard Rebar ShakerTM
Rebar Shaker
1. One person centers rebar with the Rebar Shaker, while another person fills the cell with grout as the rebar shaker is turned on.
When the cell is filled with grout, it's DONE!
No Mess! No Clean up! Two man operation not three!
Pencil Head
1. One person centers the rebar in the cell while another person fills the cell with grout.
2. After step one is finished, and there is room, another person lowers a pencil head and shaft down to bottom of cell and withdraws the grout covered head and shaft.
3. Since the concrete slumped down due to vibration, a person must now come back and fill the cell with more grout.
4. Clean up - What a time consuming mess!
The Most Efficient Way To Vibrate grout In A Blockwall Cell or Wall
...Turn Your Rebar Into A Vibrator
(For rebar up to 7/8 inch diameter in most applications)
Eliminate the time and mess of lowering a concrete vibrator into a cell containing a rebar and filled with grout. The splashes caused by the withdrawal of the vibrator
are slippery, dangerous and time consuming to cleanup.
The Rebar ShakerTM simply slipped over the top of the rebar, vibrates and
consolidates grout in 5 to 7 seconds.
Tremendous savings in man-hours, from filling and refilling cells, clean-up and lost time due to injury from slips and falls are realized through the use of the Rebar ShakerTM.
No human errors such as skipping cells and poor vibrating techniques (i.e. not letting vibrator touch the bottom or withdrawing to fast), which result in poor consolidation and a weak bond between
the rebar and the grout.
|
Oztec Rebar Shaker
|
|
HRBS
|
Rebar Shaker Head
|
|
FSRBS05
|
5' Rebar Shaker Shaft(Use with 1.2 OZ)
|
|
FSRBS07
|
7' Rebar Shaker Shaft(Use with BP-35)
|
Shown with optional Dust Collection System (CG12E Only)
Concrete Ceiling Grinder - Model CG-12
-
Grinds ceilings 7 feet to 12 feet high.
-
Swivel adjustment allows grinding up to and along edge of the wall.
-
Self aligning grinding head makes full surface contact easy to operate because it needs no adjustment.
-
Electric Model CG12E with 2 HP Baldor motor.
-
Gas Model CG12G with 3HP Honda engine.
Oztec introduces a dust collection attachment for its CG12 Ceiling Grinder. Fitted to the grinding head it provides a safer and more productive work
environment. Fits all electric models of Oztec Ceiling Grinders. The Heavy Duty Vacuum is specifically designed for concrete grinding and maximum dust collection.
|
Self aligning, grinding head makes full surface contact easy to operate because it needs no adjustment.
|
|
Welded frame is fully adjustable and configurable to any ceiling grinding requirement.
|
|
Electric Model CG12E with 2 HP Baldor motor with thermal overload protection.
|
|
Gas Model CG12G with 3 HP Honda engine.
|
|
Models
|
|
CG12E
|
7" - 2HP ELECTRIC - CEILING GRINDER (NO DUST COLLECTION)
|
|
CG12G
|
7" - 3HP HONGA GAS - CEILING GRINDER (NO DUST COLLECTION )
|
|
CG12E-DC7
|
7" - 2HP ELECTRIC - CEILING GRINDER WITH DUST COLLECTION
|
|
CG12E-DC7-H
|
7" - 2HP ELECTRIC - "HEPA" CEILING GRINDER ELEC WIL DUCT COLLECTION
|
|
227A1
|
7" DUST COLLECTION KIT FOR CG12E
|
|
227A1-H
|
"HEPA" - 7" DUST COLLECTION KIT FOR CG12E
|
|
224A1
|
4" RISER FOR CG12E
|
