This 1,300 lb. heavy-duty cast iron planer offers rock solid rigidity and accurate planing for years to come. The hinged top allows easy access to the rollers and
knives. The hood comes standard with a 5 inch dust port for easy attachment to any dust collection system. The cutterhead is complete with four high speed steel knives and turns at 4,800 rpm
producing 19,200 cuts per minute. The anti-kick back fingers and pressure bar are located in close proximity to the cutterhead for an exceptional finish. The well designed infeed and outfeed
rollers are fitted with roller bearings for long roller life. The sectional infeed and chip breaker are specially designed to allow multiple boards to be planed at the same time. The adjustable bed
roller facilitates both rough and finish planing. The solid steel outfeed roller is machined with small serrations to insure a smooth finish yet provide positive feeding. The two-speed gearbox with
machined detents is quickly changed up front when switching from rough to finish work. You may easily raise the massive ribbed cast iron, ground finished table 1 /16 with each turn of the hand
wheel. The model 201 is available with a 7-1 /2 horsepower, 3-phase or single-phase motor. This planer is perfect for the small to medium shop with continuous planing requirements.
Features:
-
2 Feed speeds - 20/30 fpm - accommodates rough and fine finish work
-
Adjustable bed rollers allow smooth feeding of rough or finished workpieces
-
All cast iron construction, the heavy cast iron table travels on two large lead scews.
-
Cast Iron construction
-
Dust chute with 5 inch port for dust collection
-
Roller bearing-mounted feed rollers for smooth operation and long life
-
Segmented infeed roller with sectional chipbreaker for planing multiple height stock
-
Straight knife cutterhead with 4 high speed steel knives gives a clean smooth cut
|
Specifications
|
|
Part Number
|
1791261
|
|
Type of Cutterhead
|
Straight Knife
|
|
Style (Type)
|
Floor
|
|
Feed Rate (FPM)
|
20/30
|
|
Maximum Depth of Cut (In.)
|
3/16
|
|
Maximum Full Width Depth of Cut (In.)
|
3/16
|
|
Maximum Planing Width (In.)
|
22
|
|
Cuts Per Minute
|
19,200
|
|
Cutterhead Diameter (In.)
|
3-1/4
|
|
Maximum Planing Thickness (In.)
|
9-1/4
|
|
Cutterhead Speed (RPM)
|
4800
|
|
Minimum Planing Length (In.)
|
10
|
|
Infeed Roller Diameter (In.)
|
3
|
|
Motor Power (HP)
|
7-1/2
|
|
Bed Rollers Adjustable from Front
|
2
|
|
Column Diameter (In.)
|
2-1/2
|
|
Dust Collection Minimum CFM Required (CFM)
|
900
|
|
Motor Phase
|
1
|
|
Prewired Voltage (V.)
|
230
|
This 1,300-pound heavy duty cast iron planer offers rock solid rigidity and accurate planing for years to come. The hinged top allows easy access to the rollers and
knives, and has a 5” dust port for easy attachment to any dust collection system. The cutterhead is a helical design with 150 four sided knife inserts – these produce a superior finish
and much quieter operation compared to conventional cutterheads, and the inserts are installed without further adjustments. The anti-kickback fingers and pressure bar are located in close proximity
to the cutterhead for an exceptional finish. Infeed and outfeed rollers are fitted with roller bearings for long life. The sectional infeed roller and chip breaker are specially designed to allow
multiple boards to be planed at the same time. The adjustable bed rollers facilitate both rough and finish planing. The solid steel outfeed roller is machined with small serrations to insure a
smooth finish yet provide positive feeding. The two-speed gearbox with machined detents is quickly changed up front when switching from rough to finish work. The massive, ribbed cast iron table is
ground finished and rises smoothly via the hand wheel. With a hefty 7-1/2 horsepower motor, the 201HH Planer is perfect for the small to medium shop with continuous planing requirements.
Features:
-
2 Feed speeds - 20/30 fpm - accommodates rough and fine finish work
-
Adjustable bed rollers allow smooth feeding of rough or finished workpieces
-
All cast iron construction, the heavy cast iron table travels on two large lead scews.
-
Cast Iron construction
-
Dust chute with 5" port for dust collection
-
Helical cutterhead with 125 four sided carbide knife inserts provides smoother, quieter cutting and finer finish than conventional systems
-
Roller bearing-mounted feed rollers for smooth operation and long life
-
Segmented infeed roller with sectional chipbreaker for planing multiple height stock
|
Specifications
|
|
Part Number
|
1791267
|
1791268
|
|
Type of Cutterhead
|
HELICAL
|
|
Style (Type)
|
Floor
|
|
Feed Rate (FPM)
|
20/30
|
|
Maximum Depth of Cut (In.)
|
3/16
|
|
Maximum Full Width Depth of Cut (In.)
|
3/16
|
|
Maximum Planing Width (In.)
|
22
|
|
Cutterhead Diameter (In.)
|
3-1/4
|
|
Maximum Planing Thickness (In.)
|
9-1/4
|
|
Cutterhead Speed (RPM)
|
4800
|
|
Minimum Planing Length (In.)
|
10
|
|
Number of Speeds
|
2
|
|
Infeed Roller Diameter (In.)
|
3
|
|
Motor Power (HP)
|
7-1/2
|
|
Bed Rollers Adjustable from Front
|
2
|
|
Maximum Height of Rollers Parallel to Tabletop (In.)
|
0.05
|
|
Column Diameter (In.)
|
2-1/2
|
|
Dust Collection Minimum CFM Required (CFM)
|
900
|
|
Motor Phase
|
1
|
3
|
|
Prewired Voltage (V.)
|
230
|
