chat now with southern tool
Technical Sales 1–800–458–3687

General Equipment FCS10 - RIP-R-STRIPPER

FC10 RIP-R-STRIPPER FLOOR STRIPPER

FC10 RIP-R-STRIPPER FLOOR STRIPPER

 

FCS10 RIP-R-STRIPPER FLOOR STRIPPER

The FCS10 RIP-R-STRIPPER is a highly productive solution for removing a wide range of floor covering materials found on both commercial and DIY projects. Its small size and light weight design makes it highly productive in hard to reach areas such as bathrooms, closets and foyers. The detachable operator handle allows for easy transport in todays smaller vehicles. Enhanced operator ergonomics and precise balance allow the FCS10 to work circles around larger stripper machines that lack the same agility and maneuverability. A wide range of straight and scoring type blades up to 10 inch cutting width are available for use on wood and concrete surfaces.

  • 10 inch maximum cutting blade width.
  • Comes with 6 in and 10 in blades (FCS16-1100 AND FSC16-1300)
  • Unitized, welded steel frame.
  • Anti-Vibe caster wheels.
  • Detachable composite operator handle.
  • Sealed ball berings.
  • Designed for easy transport in small vehicles.

FCS10 RIP-R-STRIPPER FLOOR STRIPPER

The FCS10 RIP-R-STRIPPER  is a highly productive solution for removing a wide range of floor covering materials found on both commercial and DIY projects. Its small size and light weight design makes it highly productive in hard to reach areas such as bathrooms, closets and foyers. The detachable operator handle allows for easy transport in todays smaller vehicles. Enhanced operator ergonomics and precise balance allow the FCS10 to work circles around larger stripper machines that lack the same agility and maneuverability. A wide range of straight and scoring type blades up to 10 inch cutting width are available for use on wood and concrete surfaces.

  • Comes with 6 in and 10 in blades (FCS16-1100 AND FSC16-1300)

Specifications:


POWER SOURCE
Type: Electric Motor: 2300W, 115VAC, 60HZ, 15 amperes
External Weight: 27 lbs (12.3 kg), less blade

General
Nominal Diameter: 3400/minute
Extension Cord: 23-1/4”L x 8-1/4”W x 43- 1/2”H (w/o blade) Dimensions: 5 inch (127 mm) OD x 1-1/2 inch W plastic


Specifications:


POWER SOURCE
Type: Electric Motor: 2300W, 115VAC, 60HZ, 15 amperes
External Weight: 27 lbs (12.3 kg), less blade

General
Nominal Diameter: 3400/minute
Extension Cord: 23-1/4 L x 8-1/4 W x 43- 1/2 H (w/o blade) Dimensions: 5 inch (127 mm) OD x 1-1/2 inch W plastic

ATTACHMENT

TYPE

VINYL

TILE

LINOLEUM

RUBBER-

BACKED

CARPET

JUTE-BACKED

CARPET

CREAMIC TILE

MASTIC

ADHESIVE

THIN

SET

MATERIAL

BUILD-UP

s-h alt
s-h alt
s-h alt
s-h alt
s-h alt
s-h alt
s-h alt
s-h alt
s-h alt
Mastic Removal
s-h alt
s-h alt
s-h alt
s-h alt
s-h alt
s-h alt
s-h alt
s-h alt
s-h alt
Dual Beveled
s-h alt
s-h alt
s-h alt
s-h alt
s-h alt
s-h alt
s-h alt
s-h alt
s-h alt
Scoring
s-h alt
s-h alt
s-h alt
s-h alt
s-h alt
s-h alt
s-h alt
s-h alt
s-h alt
Single Beveled
                 

Strip Coatings From Surfaces

s-h alt
 
Mastic Removal
The single beveled mastic removal blade is utilized to remove a wide variety of  adhesives, mastics and material residues from concrete surfaces. The steep angle increases the cutting edge position relative to the floor surfaces. The angle increases allows the blade to better penitrate the material and then shear and scrape it from the floor surface. the cutting edge faces down toward the floor surface. Angled mastic blades are utilized on concrete surface ONLY! Not intended to be used on a wood surface; blade will only dig into surface. The blade will NOT flip over.
Specifications: FCS-1200

Material:
Laser cut, heat-treated, steel, sharpen edge
Application:
Mastic, adhesive and material build-up removal.
Hints:
Not intended to remove actual floor covering materials. Remove remaining material residue and mastic/adhesive on concrete floor ONLY. Steeper blade angle increases material removal rates over other blade configurations.
Dimensions:
4 inch x 6 inch x 1.5mm nominal

Strip Coatings From Surfaces

s-h alt
 
Dual Beveled
The dual beveled blade is utilized to remove a wide variety of VCT and linoleum tiles along with general material removeal from concrete and wood surfaces. There are two types: bevel up for concrete and bevel down for wood. This allows the blade to skim over the surface and minimize an tendency to gouge or dig into the material. The blade will flip over.
Specifications: FCS16-1100

Material:
Laser cut, heat-treated, steel, sharpen edge
Application:
General purpose material removal. Narrow width increases productivity against difficult to remove materials. Dual edges double blade service life.
Hints:
Position beveled edge UP on concrete floor. Position beveled edge DOWN on wood floor. Blade can be field sharpened.
Dimensions:
4 inch x 6 inch x 1.5mm nominal

Strip Coatings From Surfaces

s-h alt
 
Scoring
The single beveled blade is utilized to remove glued type carpets and soft sheet types (PVC, rubber, linoleum, etc) materials from concrete to wood surfaces. There are two types: bevel up for concrete and bevel down for wood. This allows the blade to skim over the surface and minimize an tendency to gouge or dig into the material. The cutting wings score the covering material to aid in removal. Specific part numbers are available for removing  covering materials from either concrete or wood surfaces. The blade will NOT flip over.
Specifications: FCS-1600

Material:
Laser cut, heat-treated, steel, sharpen edge
Application:
Remove rubber-back carpet and linoleum.
Hints:
Blades are NOT interchangeable for use on concrete and wood floors. Use proper blade for application. Position beveled edge UP on concrete floor. Position beveled edge DOWN on wood floor. Blade can be field sharpened.
Dimensions:
3 inch x 8 inch x 1.5mm nominal

Strip Coatings From Surfaces

s-h alt
 
Single Beveled
The single beveled blade is utilized to remove a wide variety of VCT and linoleum tiles along with general material removeal from concrete and wood surfaces. There are two types: bevel up for concrete and bevel down for wood. This allows the blade to skim over the surface and minimize an tendency to gouge or dig into the material. The blade will NOT flip over.
Specifications: FCS-1300

Material:
Laser cut, heat-treated, steel, sharpen edge
Application:
General purpose material removal. Wider width increases productivity against easy to remove materials.
Hints:
Blade can be used on both concrete and wood floors. Position beveled edge UP on concrete floor. Position beveled edge DOWN on wood floor. Blade can be field sharpened.
Dimensions:
3 inch x 10 inch x 1.5mm nominal

 

FCS10 - Accessories
FCS16-1100 BLADE, STRAIGHT, 4L, REPLACEMENT
FCS16-1200 BLADE, ANGLED, 6L, REPLACEMENT
FCS16-1300 BLADE, STRAIGHT, 10L, REPLACEMENT
FCS16-1500 BLADE, SCORING, CEMENT, 8L, REPLACEMENT
FCS16-1600 BLADE, SCORING, WOOD, 8L, REPLACEMENT

 

LIMITED PRODUCT WARRANTY

GENERAL EQUIPMENT COMPANY makes the following limited warranty to the original purchaser of each new and unused light construction equipment product:

GENERAL EQUIPMENT COMPANY MAKES NO WARRANTY THAT THE LIGHT CONSTRUCTION PRODUCTS SOLD HEREUNDER SHALL BE MERCHANTABLE OR THAT SUCH PRODUCTS SHALL BE FIT FOR ANY PARTICULAR PURPOSE AND THERE ARE NO WARRANTIES EXPRESSED OR IMPLIED MADE OTHER THAN ITS STANDARD, LIMITED WARRANTY.

WHAT THE LIMITED WARRANTY COVERS

GENERAL EQUIPMENT COMPANY warrants that each new and unused light construction equipment product and or accessory product sold by it: A) to be free from defects in material and workmanship under normal use/service for a period of two (2) years from date of purchase: B) to warrant the labor expenses associated with defects in material and workmanship for a period of one (1) year from date of purchase. The obligation under this warranty being limited to current flat labor rates and the replacement and/or repair at its Owatonna, Minnesota, factory site, or at an authorized dealer designated by it, of such part or parts as shall appear upon inspection to have been defective in material or workmanship at the time sold, provided that the part or parts claimed defective are returned to the inspection point, transportation charges prepaid. At the time of requesting warranty service, the purchaser must present evidence of the purchase date of the part or parts submitted for warranty inspection.

The only remedies the purchaser has in connection with the breach of performance of any warranty for the light construction equipment products sold by GENERAL EQUIPMENT COMPANY are those set forth in this document. In no event will GENERAL EQUIPMENT COMPANY, its authorized dealer or representative, or any company affiliated with GENERAL EQUIPMENT COMPANY be held liable for any incidental or consequential damages or injuries.

WHAT THE LIMITED WARRANTY DOES NOT COVER

This warranty does not cover depreciation or damage caused by: normal wear, accident, improper protection in storage, improper use, alterations, tampering, the environment, improper maintenance, lack of maintenance or incidental costs incurred by the original purchaser while the light construction equipment product is being examined and or repaired under warranty. In addition to the above limitations and/or exclusions, the following basic product components are not covered by the limited warranty:

1) Parts and/or components subject to wear with normal usage, but not specifically limited to the following:

a) High impact/wear related components including, but not limited to: V-belts, flails, flail rods and flail drums.
b) High abrasion/wear related components including, but not limited to: augers, auger flighting and boring heads.
c) Engine throttle control cable assembly and related control devices.
d) Centrifugal clutch components including, but not limited to: shoes, springs, drum and motor assembly.

2) Parts and labor for scheduled and general maintenance services as defined in the applicable Operators Manual.

3) Engines, motors, controls and other accessories sold with, attached to, or operated with a light construction equipment product sold by GENERAL EQUIPMENT COMPANY and warranted separately by the Original Equipment Manufacturer (OEM) per its respective warranty program. Contact the Customer Service Department of GENERAL EQUIPMENT COMPANY for assistance in obtaining specific OEM warranty coverage.

This limited warranty gives you specific legal rights and may also have other rights which may vary from state to state. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. These limitations may not apply to the original purchaser.

FCS10
STRIPPER, COVERING, FLOOR ** SHIP BY LTL TRUCK - 94.5 LBS APPROX WEIGHT
Mfg. item #: FCS10
GENFCS10
Call for freight quote on this item or we will confirm freight charges before shipping.1
$1,263.28

8
FCS16-1100
FCS16-1100 REPLACEMENT STRAIGHT BEVELED CUTTING EDGE BLADE, 4 LENGTH X 6 WIDTH X 1.5MM THICK, FOR RIP-R-STRIPPER FLOOR COVERING STRIPPER
Mfg. item #: FCS16-1100
GENFCS16-1100
FREE shipping when ordered with a machine from this manufacturer.20
$15.09

8
FCS16-1200
FCS16-1200 REPLACEMENT ANGLED MASTIC REMOVAL BLADE, 4 LENGTH X 6 WIDTH X 1.5MM THICK, FOR RIP-R-STRIPPER FLOOR COVERING STRIPPER
Mfg. item #: FCS16-1200
GENFCS16-1200
FREE shipping when ordered with a machine from this manufacturer.20
$26.74

8
FCS16-1300
FCS16-1300 REPLACEMENT STRAIGHT BEVELED CUTTING EDGE BLADE, 3 LENGTH X 10 WIDTH X 1.5MM THICK, FOR RIP-R-STRIPPER FLOOR COVERING STRIPPER
Mfg. item #: FCS16-1300
GENFCS16-1300
FREE shipping when ordered with a machine from this manufacturer.20
$15.77

8
FCS16-1500
FCS16-1500 REPLACEMENT STRAIGHT BEVELED CEMENT SCORING BLADE, 3 LENGTH X 8 WIDTH X 1.5MM THICK, FOR RIP-R-STRIPPER FLOOR COVERING STRIPPER
Mfg. item #: FCS16-1500
GENFCS16-1500
FREE shipping when ordered with a machine from this manufacturer.20
$34.29

8
FCS16-1600
FCS16-1600 REPLACEMENT STRAIGHT BEVELED WOOD SCORING BLADE, 3 LENGTH X 8 WIDTH X 1.5MM THICK, FOR RIP-R-STRIPPER FLOOR COVERING STRIPPER
Mfg. item #: FCS16-1600
GENFCS16-1600
FREE shipping when ordered with a machine from this manufacturer.20
$27.44

8
Copyright © 2018 Smith-Hamilton, Inc
0.006 180807 13:42