FCS16 RIP-R-STRIPPER FLOOR STRIPPER
Welded, unitized frame. Adjustable operator handle folds for transport. Direct-drive, random orbit action; 14 lbs external weight. Includes 1 each, part number
FCS16-1100, 4" x 6" straight blade 1 each, part number FCS16-1300, 3" x 10" straight blade.
FCS16 Rip-R-Stripper, an eletric-powered floor-covering scraper. Ideal for removing such materials as carpet, ceramic tile, linoleum, the Rip-R-Stripper offers high productivity, ergonomic design and multiple removal accessories.
Built with a 3/4-horsepower, 115/230 VAC, 60Hertz electric motor, the Rip-R-Stripper features high productivity, yet low noise levels. With an exciter unit mounted directly to the driveshaft, the scraper uses downward force to bore into and strip away the applied floor covering and adhesive. External weights can be used to provide extra force for removing tough residue and to increase material removal rates. Producing less than 70 dBA (decibel level), operation noise is quiet and safe.
Ergonomic design provided a more pleasant operator experience to increase work stamina and minimize occupational injury. The comfortable operator's handle offers a full-width, tubular constructions that increases leverage and control, while the handle-grip configuration is designed to optimize wrist strength and reduce fatigue. The adjustable handle height caters to operators of any build, helping to prevent lower back strain. Further increasing safety and productivity rates, the Back-Saver blade control system allows adjustment of the blade angle during use. This eliminates having to stop the machine and manually change blade angles or adjust linkages.
Downlaod (PDF) File
FCS16 RIP-R-STRIPPER FLOOR STRIPPER
Welded, unitized frame. Adjustable operator handle folds for transport. Direct-drive, random orbit action; 14 lbs external weight. Includes 1 each, part number FCS16-1100, 4" x 6" straight blade 1
each, part number FCS16-1300, 3" x 10" straight blade.
Specifications:
POWER SOURCE
Type: Lesson, single phase, 115/230 VAC, 60 Hz
Horse Power: 3/4HP (.56kw)
FRAME
Structure: Unitized, welded steel plate
Bearings: Zerk type fittings
Drive System: Exciter unit mounted directly to motor driveshaft
External Weight: 15 lbs (6.8kw) steel block
Wheel Scraper: 2 inch, externally mounted, fully adjustable for wear compensation Operator Handle: Adjustable height and foldable
General
Width: 14-1/2 inch (368 mm)
Width (at operator handle): 23 inch (584 mm)
height (at operator handle extension): 42 inch (1067 mm)
Length (handle folded): 24 inch (610 mm)
Length (at operator configuration): 34 inch (864 mm)
Specifications:
POWER SOURCE |
ATTACHMENT TYPE |
VINYL TILE |
LINOLEUM |
RUBBER- BACKED CARPET |
JUTE-BACKED CARPET |
CREAMIC TILE
|
MASTIC ADHESIVE |
THIN SET |
MATERIAL BUILD-UP |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
Mastic Removal
|
||||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
Dual Beveled | ||||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
Scoring | ||||||||
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
Single Beveled | ||||||||
Strip Coatings From Surfaces |
|
![]() |
|
Mastic Removal | |
The single beveled mastic removal blade is utilized to remove a wide variety of adhesives, mastics and material residues from concrete surfaces. The steep angle increases the cutting
edge position relative to the floor surfaces. The angle increases allows the blade to better penitrate the material and then shear and scrape it from the floor surface. the cutting edge
faces down toward the floor surface. Angled mastic blades are utilized on concrete surface ONLY! Not intended to be used on a wood surface; blade will only dig into surface. The blade will
NOT flip over.
|
|
Specifications: | FCS-1200 |
|
|
Material:
|
Laser cut, heat-treated, steel, sharpen edge |
Application:
|
Mastic, adhesive and material build-up removal.
|
Hints:
|
Not intended to remove actual floor covering materials. Remove remaining material residue and mastic/adhesive on concrete floor ONLY. Steeper blade angle increases material removal rates
over other blade configurations.
|
Dimensions:
|
4 inch x 6 inch x 1.5mm nominal |
Strip Coatings From Surfaces |
|
![]() |
|
Dual Beveled | |
The dual beveled blade is utilized to remove a wide variety of VCT and linoleum tiles along with general material removeal from concrete and wood surfaces. There are two types: bevel up for
concrete and bevel down for wood. This allows the blade to skim over the surface and minimize an tendency to gouge or dig into the material. The blade will flip over.
|
|
Specifications: | FCS16-1100 |
|
|
Material:
|
Laser cut, heat-treated, steel, sharpen edge |
Application:
|
General purpose material removal. Narrow width increases productivity against difficult to remove materials. Dual edges double blade service life.
|
Hints:
|
Position beveled edge UP on concrete floor. Position beveled edge DOWN on wood floor. Blade can be field sharpened.
|
Dimensions:
|
4 inch x 6 inch x 1.5mm nominal |
Strip Coatings From Surfaces |
|
![]() |
|
Scoring | |
The single beveled blade is utilized to remove glued type carpets and soft sheet types (PVC, rubber, linoleum, etc) materials from concrete to wood surfaces. There are two types: bevel up
for concrete and bevel down for wood. This allows the blade to skim over the surface and minimize an tendency to gouge or dig into the material. The cutting wings score the covering
material to aid in removal. Specific part numbers are available for removing covering materials from either concrete or wood surfaces. The blade will NOT flip over.
|
|
Specifications: | FCS-1600 |
|
|
Material:
|
Laser cut, heat-treated, steel, sharpen edge |
Application:
|
Remove rubber-back carpet and linoleum. |
Hints:
|
Blades are NOT interchangeable for use on concrete and wood floors. Use proper blade for application. Position beveled edge UP on concrete floor. Position beveled edge DOWN on wood floor.
Blade can be field sharpened.
|
Dimensions:
|
3 inch x 8 inch x 1.5mm nominal |
Strip Coatings From Surfaces |
|
![]() |
|
Single Beveled | |
The single beveled blade is utilized to remove a wide variety of VCT and linoleum tiles along with general material removeal from concrete and wood surfaces. There are two types: bevel up
for concrete and bevel down for wood. This allows the blade to skim over the surface and minimize an tendency to gouge or dig into the material. The blade will NOT flip over.
|
|
Specifications: | FCS-1300 |
|
|
Material:
|
Laser cut, heat-treated, steel, sharpen edge |
Application:
|
General purpose material removal. Wider width increases productivity against easy to remove materials. |
Hints:
|
Blade can be used on both concrete and wood floors. Position beveled edge UP on concrete floor. Position beveled edge DOWN on wood floor. Blade can be field sharpened. |
Dimensions:
|
3 inch x 10 inch x 1.5mm nominal |
Models and Accessories | |
---|---|
FCS16 | STRIPPER, COVERING, FLOOR, .75HP, 115VAC, 60HZ SHIP BY LTL TRUCK - 185 LBS APPROX WEIGHT |
FCS16-1100 | FCS16-1100Replacement Straight Beveled Cutting Edge Blade, 4 inch Length x 6 inch Width x 1.5mm Thick, For Rip-R-Stripper Floor Covering Stripper |
FCS16-1200 | FCS16-1200 Replacement Angled Mastic Removal Blade, 4 inch Length x 6 inch Width x 1.5mm Thick, For Rip-R-Stripper Floor Covering Stripper |
FCS16-1300 | FCS16-1300 Replacement Straight Beveled Cutting Edge Blade, 3 inch Length x 10 inch Width x 1.5mm Thick, For Rip-R-Stripper Floor Covering Stripper |
FCS16-1500 | FCS16-1500 Replacement Straight Beveled Cement Scoring Blade, 3 inch Length x 8 inch Width x 1.5mm Thick, For Rip-R-Stripper Floor Covering Stripper |
FCS16-1600 | FCS16-1600 Replacement Straight Beveled Wood Scoring Blade, 3 inch Length x 8 inch Width x 1.5mm Thick, For Rip-R-Stripper Floor Covering Stripper |