Wet Cutting Saws: 10" Wet Abrasive Cutoff Machines
Complete with 3 HP TEFC motor, coolant tray, magnetic starter with 110 volt at the pushbuttons, steel stand, settling tank and pump
Ideal For METALLURGICAL LABS as well as for Exotic Alloys. Typical wet cutting speeds are 30 seconds per square inch of material based on application.
Capacity: 1" solids and 2" shapes.
Coolant flow can be regulated and directed to both sides of the cut for optimum performance.
10" Wet Cutoff/Met Lab. Catalog Page
Wet Cutting Saws: 10" Wet Abrasive Cutoff Machines
Complete with 3 HP TEFC motor, coolant tray, magnetic starter with 110 volt at the pushbuttons, steel stand, settling tank and pump
|
Product #
|
Description
|
|
101020
|
10" WET 3 HP 115 VOLT 1 Ph, STAND, MAG STARTER
|
|
101021
|
10" WET 3 HP 230 VOLT 1 Ph, STAND, MAG STARTER
|
|
101022
|
10" WET 3 HP 208 VOLT 3 Ph, STAND, MAG STARTER
|
|
101023
|
10" WET 3 HP 230 VOLT 3 Ph, STAND, MAG STARTER
|
|
101024
|
10" WET 3 HP 380 VOLT 3 Ph 50 HZ, STAND, MAG STARTER
|
|
101025
|
10" WET 3 HP 440 VOLT 3 Ph, STAND, MAG STARTER
|
|
101027
|
10" WET 3 HP 575 VOLT 3 Ph, STAND, MAG STARTER
|
Abrasive Wheels: Wet Non-Reinforced & Reinforced Abrasive Cutting Wheels
Link for Everett Wet & Dry Cut Abrasive Blades
All the cutting wheel grades have been developed and extensively tested to produce quality
cuts on a wide range of material alloys, sizes and shapes.
As an abrasive wheel manufacturer, we have other grades of wet and dry abrasive cutoff wheels to meet your specific requirements. Contact the factory for special diameter, thickness, arbor hole and
drive pin requirements of abrasive wheels.
Non-Reinforced Rubber Bonded
Cutting Wheels for Wet Cutting
The following cutoff wheels cannot be fiberglass reinforced.
Use only on well guarded machines with extreme caution and personal protection.
|
Grade
|
|
Description of Cutting Wheels
|
|
|
#1410
|
|
For wet metallurgical cutting. Also excellent for high quality wet cuts on hardened material, tubing. Available in most sizes.
|
|
|
|
|
|
|
|
#1115
|
|
Calendered rubber wheel specially formulated for general purpose use on our
10ÃÂÉ¢ÃÂÉâÂÄÂöÃÂÉâÂÄÂûÃÂÉâÂÄÂöÃÂɹ
wet saw.
|
|
|
|
|
|
|
|
#1329
|
|
General purpose calendered rubber wheel, designed for wet
cutting solids, heavy wall shapes and tubing. Produces fine cut, excellent for use on wet, power head machines. Available in 14", 16", 20", and 26".
|
|
|
|
|
|
|
|
#60
|
|
General purpose pressed rubber wheel designed for wet
cutting solids, heavy wall shapes and tubing. Larger grit sizes generally produce coarser cut than #1329. Available in all sizes.
|
|
|
|
|
|
|
|
#91
|
|
Designed for non-ferrous cutting - copper cutting, brass cutting, etc., rubber bond silicon carbide. Available in all sizes.
|
|
|
|
|
|
|
Fiberglass Reinforced Wet
Abrasive Cutoff Wheels
|
Grade
|
|
Description of Cutting Wheels
|
|
|
93FG
|
|
Fiberglass internally reinforced cloth is molded in the center of the abrasive wheel for break resistance. Pressed resin-rubber abrasive wheel; excellent for high quality
wet cuts on hardened material, also wet metallurgical cutting. Available in most sizes.
|
