Dry Cutting: 20"-22" Contractor's Abrasive Cutoff Machine
The Contractor's Model was designed for job site reliability and performance.
Complete with 7.5 or 10 HP TEFC motor, magnetic starter with 110 volt at the pushbuttons, V shaped chain hold-down vise, steel stand
For Cutting Up to 6" Pipe and Conduit
This rugged, but portable, Everett model was specially designed for the job site. The Contractorâs Model comes complete with magnetic starter with 110 volt at the pushbutton,
stand and foot pedal operated vise. The special high-torque motor is totally enclosed and fan cooled.
20"-22" Contractor's Model Catalog Page
20"-22" Contractor Abrasive Cutoff & Accessories
7.5 & 10 HP Models
Complete with motor, magnetic starter with 110 volt at the pushbuttons, âVâ shaped chain hold-down vise, steel stand
|
Product #
|
Description
|
|
7-1/2 HP Models (1 and 3 Phase Available)
|
|
520041
|
20" CONT 7.5 HP 230 VOLT 1 Ph, STAND, MAG STARTER
|
|
520042
|
20" CONT 7.5 HP 208 VOLT 3 Ph, STAND, MAG STARTER
|
|
520043
|
20" CONT 7.5 HP 230 VOLT 3 Ph, STAND, MAG STARTER
|
|
520044
|
20" CONT 7.5 HP 380 VOLT 3 Ph 50 HZ, STAND, MAG STARTER
|
|
520045
|
20" CONT 7.5 HP 440 VOLT 3 Ph, STAND, MAG STARTER
|
|
520047
|
20" CONT 7.5 HP 575 VOLT 3 Ph, STAND, MAG STARTER
|
|
10 HP Models (3 Phase Only)
|
|
520052
|
20" CONT 10 HP 208 VOLT 3 Ph, STAND, MAG STARTER
|
|
520053
|
20" CONT 10 HP 230 VOLT 3 Ph, STAND, MAG STARTER
|
|
520054
|
20" CONT 10 HP 380 VOLT 3 Ph 50 HZ, STAND, MAG STARTER
|
|
520055
|
20" CONT 10 HP 440 VOLT 3 Ph, STAND, MAG STARTER
|
|
520057
|
20" CONT 10 HP 575 VOLT 3 Ph, STAND, MAG STARTER
|
Abrasive Wheels: Dry Reinforced Abrasive Cutting Wheels
Link for Everett Dry Cut Abrasive Blades
All the cutting wheel grades have been developed and extensively tested to produce quality
cuts on a wide range of material alloys, sizes and shapes.
As a manufacturer of abrasive wheels, we have other grades of wet and dry abrasive wheels to meet your specific requirements. Contact us for special diameter, thickness, arbor hole and drive pin
requirements of abrasive wheels.
Fiberglass Internally Reinforced Resinoid Bond Aluminum Oxide Cutting Wheels
Woven fiberglass cloth is molded in the center of the abrasive wheel for break resistance.
|
Grade
|
|
Description of Cutting Wheels
|
|
|
45FG
|
|
For general purpose cutting
|
|
|
|
|
|
|
|
23020FG
|
|
Designed for use on machines with POWERHEAD (automatic wheel feed) where free cutting ability is needed because of constant feed pressure
|
|
|
|
|
|
|
|
2069FG
|
|
Ideal for heavier wall shapes and tubing
|
|
|
|
|
|
|
|
T32 FG
|
|
For cutting thin wall shapes and thin wall tubing
|
|
|
|
|
|
|
|
GTK-7FG
|
|
Excellent for high quality dry cuts on stainless tubing and other thin wall tubing
|
|
Fiberglass Externally Reinforced Cutting Wheels
Woven fiberglass cloth is applied externally on both sides of the abrasive wheel for break resistance.
|
Grade
|
|
Description of Cutting Wheels
|
|
|
45FGE
|
|
For general purpose cutting
|
|
|
|
|
|
|
|
23020FGE
|
|
Designed for use on cutoff saws with POWERHEAD (automatic
wheel feed) where free cutting ability is needed because of constant feed pressure
|
|
|
|
|
|
|
|
2069FGE
|
|
Ideal for heavier wall shapes and tubing
|
|
|
|
|
|
|
|
T32 FGE
|
|
For cutting thin wall shapes and thin wall tubing
|
|
|
|
|
|
|
|
GTK-7FGE
|
|
Excellent for high quality dry cuts on stainless tubing and other thin wall tubing
|
