Wet Cutting Saws:  20"-22" Wet Abrasive Oscillating Cutoff Machines

Complete with 20 HP TEFC motor, magnetic starter with 110 volt at the pushbuttons, air operated V shaped chain hold-down vise, coolant tray, settling tank and pump

Typical wet cutting speeds are 30 seconds per square inch of material based on application

The cutting wheels on these Everett wet saw models are cooled by rotating through a water box with hinged adjustable sides. The water ejector and the wheel itself combine to throw the coolant into the cut and over the material to assure total cooling. The flow and discharge are easily regulated with the control valve and by adjusting the sides of the water box.

Capacity: 3" solids. Most 7" shapes

20"-22" Wet Abrasive Oscillating Cutoff Machines

With patented Oscillation (OSC): For improved cutting, reduced burr and longer wheel life.

Complete with 20 HP TEFC motor, magnetic starter with 110 volt at the pushbuttons, air operated V shaped chain hold-down vise, coolant tray, settling tank and pump

Product #	Description
211262	20" WET OSC 20 HP 208 VOLT 3  Ph, MAG STARTER
211263	20" WET OSC 20 HP 230 VOLT 3  Ph, MAG STARTER
211264	20" WET OSC 20 HP 380 VOLT 3  Ph 50HZ, MAG STARTER
211265	20" WET OSC 20 HP 440 VOLT 3  Ph, MAG STARTER
211267	20" WET OSC 20 HP 575 VOLT 3  Ph, MAG STARTER

Hydraulic Power Head Models (PH)
with patented Oscillation (OSC): For improved cutting, reduced burr and longer wheel life.

Complete with 20 HP TEFC motor, magnetic starter with 110 volt at the pushbuttons, air operated V  shaped chain hold-down vise, coolant tray, settling tank and pump

Product #	Description
213262	20" WET PH OSC 20 HP 208 VOLT 3  Ph, MAG STARTER
213263	20" WET PH OSC 20 HP 230 VOLT 3  Ph, MAG STARTER
213264	20" WET PH OSC 20 HP 380 VOLT 3  Ph 50HZ, MAG STARTER
213265	20" WET PH OSC 20 HP 440 VOLT 3  Ph, MAG STARTER
213267	20" WET PH OSC 20 HP 575 VOLT 3  Ph, MAG STARTER

Hydraulic Power Head Models (PH)
with patented Wheel Wear Compensator (WWC)
Oscillation: For improved cutting, reduced burr and longer wheel life.

Complete with 20 HP TEFC motor, magnetic starter with 110 volt at the pushbuttons, air operated V shaped chain hold-down vise, coolant tray, settling tank and pump

Product #	Description
215262	20" WET PH WWC OSC 20 HP 208 VOLT 3  Ph, MAG STARTER
215263	20" WET PH WWC OSC 20 HP 230 VOLT 3  Ph, MAG STARTER
215264	20" WET PH WWC OSC 20 HP 380 VOLT 3  Ph 50HZ, MAG STARTER
215265	20" WET PH WWC OSC 20 HP 440 VOLT 3  Ph, MAG STARTER
215267	20" WET PH WWC OSC 20 HP 575 VOLT 3  Ph, MAG STARTER

Note:
Work Length Gage automatically swings up out of the way when the part is cut.

Abrasive Wheels:  Wet Non-Reinforced & Reinforced Abrasive Cutting Wheels

Link for Everett Wet & Dry Cut Abrasive Blades

All the cutting wheel grades have been developed and extensively tested to produce quality
cuts on a wide range of material alloys, sizes and shapes.

As an abrasive wheel manufacturer, we have other grades of wet and dry abrasive cutoff wheels to meet your specific requirements. Contact the factory for special diameter, thickness, arbor hole and drive pin requirements of abrasive wheels.

Non-Reinforced Rubber Bonded
Cutting Wheels for Wet Cutting
The following cutoff wheels cannot be fiberglass reinforced.
Use only on well guarded machines with extreme caution and personal protection.

Fiberglass Reinforced Wet
Abrasive Cutoff Wheels