Technical Sales 1–800–458–3687

Laguna Industrial Dust Collectors

t-flux 5 cyclone T|Flux: 10 Cyclone I|Flux: 5 Elite I|Flux: 10 Elite X|Flux: 10HP
T-Flux 5 Cyclone
5HP, 220V Motor, 4295CFM of Air Flow, 22.4 Full Load Amperage Draw 		T-Flux 5 Cyclone
 10HP, 220V Motor, 6957CFM of Air Flow, 30 Full Load Amperage Draw 		I-Flux 5 Elite
 5HP TEFC Motor, Doubled Filter Area of 286.3 ft², CE NFPA Safety Certifications 		I-Flux 10 Elite
10HP TEFC Motor, Doubled Filter Area of 409 ft², CE NFPA Safety Certifications

X-Flux 10 HP
10HP, 220V Motor , 8070CFM of Air Flow, 28 Full Load Amperage Draw

Click here for classic woodworking laguna dust Collectors

 

Models
MDCTF52201 T|flux:5 Cyclone Dust Collector
MDCTF102203 T|flux:10 Cyclone Dust Collector
MDCXF102203 X|flux:10 Cyclone Dust Collector
MDCIF52203 I|Flux: 5 Elite Dust Collector
MDCIF102203 I|Flux: 10 Elite Dust Collector

 

T|Flux: 5 Cyclone

 TFlux: 5 Cyclone

The TFlux series from Laguna starts to get serious. The Titan cyclones are geared towards clients who desire a single central unit for the entire shop. The T|Flux cyclones are equipped with a 10 inch port that splits into 3 x 4 inch, allowing you to run a large diameter pipe system throughout your shop with drops to the individual stations.

All models are outfitted with smart drums which alert the user when the drums reach capacity. Automatic canister cleaning is controlled by a timer that turns on every work hour and runs 10 seconds clockwise and counter clockwise. The 1 micron canister has a huge surface area and filtrates 99.97 percent of particles ranging from 0.2 to 2 microns. Smart Drums comes standard with high quality casters and feature our unique quick disconnect design.

Specifications:

  • Shop Setting CFM: 2450
  • Inlet CFM: 4295
  • Max Static Pressure (Inches of Water): 12.1 inch
  • Impeller/Fan Size: 16 inch
  • Impeller Material: Steel
  • Impeller Type: Radial Fin
  • Balanced To: ISO 1940
  • Inlet Diameter: 10 inch
  • Drum Capacity: 54 Gal
  • Octagon Drum: Low Pressure Suction
  • Drum Collection Bag (Dia. x L): Plastic Bag (740 x 1300mmL)
  • Canister Filter Type: Black 1 Micron
  • Filtration Efficiency: 1.2-2 Micron at 99.97 percent
  • MERV Rating: 12 
  • Canister Diameter: 600mm (23.62″) 
  • Canister Length: 1200mm (47.24″) 
  • Filter Surface Area: 15m²/162ft² 
  • Canister Cleaning: Auto Clean (Gear Motor)/ Cleans every hour 10 sec clockwise, 10 sec counter-clockwise 
  • Canister Filter Lower Dust Collection: Plastic Bag (610 x 600mmL) 
  • Wheels: None 
  • US/CSA Approved: Yes 
  • Decibel Reading: 76dB(A)(at9.8ft) 
  • Machine Weight: 325 kgs/717 lbs
  • Shipping Weight: 430 kgs / 948 lbs
  • Shipping Dimensions (L x W x H): 75 x 39 x 80 inch
  • Assembled Dimensions (L x W x H): 73 x 39 x 111 inch (1845 x 989 x 2810mm)

 

T|Flux: 10 Cyclone

 T|Flux: 10 Cyclone

The T|Flux series from Laguna starts to get serious. The Titan cyclones are geared towards clients who desire a single central unit for the entire shop The T|Flux cyclones are equipped with a 12 inch port that splits into 3 x 4 inch, allowing you to run a large diameter pipe system throughout your shop with drops to the individual stations.

 

All models are outfitted with smart drums which alert the user when the drums reach capacity. Automatic canister cleaning is controlled by a timer that turns on every work hour and runs 10 seconds clockwise and counter clockwise. The 1 micron canister has a huge surface area and filtrates 99.97 percent of particles ranging from 0.2 to 2 microns. Smart Drums comes standard with high quality casters and feature our unique quick disconnect design.

Specifications:

  • Shop Setting CFM: 4030
  • Inlet CFM: 6957
  • Max Static Pressure (Inches of Water): 16.8 inch
  • Impeller/Fan Size: 18-1/2 inch
  • Impeller Material: Steel
  • Impeller Type: Radial Fin
  • Balanced To: ISO 1940
  • Inlet Diameter: 12 inch
  • Drum Capacity: 54 Gal x 2 Sets
  • Octagon Drum: Low Pressure
  • Drum Collection Bag (Dia. x L): Plastic Bag (740 x 1300mmL)
  • Canister Filter Type: Black 1 Micron
  • Filtration Efficiency: 0.2-2 Micron
  • MERV Rating: 12 
  • Canister Diameter: 750mm (29.53 inch)
  • Canister Length: 1200mm (47.24 inch) 
  • Filter Surface Area: 19.2 m²/207 ft²
  • Canister Cleaning: Auto Clean (Gear Motor)/ Cleans every hour 10 sec clockwise, 10 sec counter-clockwise 
  • Canister Filter Lower Dust Collection: Plastic Bag(740 x 600mmL)
  • Wheels: None 
  • US/CSA Approved: Yes 
  • Decibel Reading: 81 dB(A)(at 9.8ft)
  • Machine Weight: 590 kgs/1301 lbs
  • Shipping Weight: 735 kgs/ 1621 lbs
  • Shipping Dimensions (L x W x H): 100 x 49 x 86 inch
  • Assembled Dimensions (L x W x H): 99.6 x 48.3 x 131.4 inch (2530 x 1225 x 3337mm)

 

IFlux 5 Elite

 IFlux 5 Elite

The iFlux|5 Elite uses an appropriate filter arrangement with 286 square feet of surface area – double that of a typical 5HP collector. To do this, we used a smaller diameter bag, and a lot more of them. This arrangement maximizes the amount of surface area possible which is vital to adequate airflow through the collector. Keeping these filters clean was addressed in the design.

Airflow 3991CFM at 5 inchwc

The 12” inlet has a net airflow of 3991CFM with a static pressure of 5 inch wc. A typical CNC Router needs a minimum requirement of 1500CFM, while a typical 37” wide belt sander would call for a minimum 2000CFM. This makes the iFlux 5 a great fit for a CNC Router based cabinet shop that would be running several tools at once.

Fine Dust Ready

With fine dust, the key is to have a large filter surface area and to keep those filters clean. The smaller tube filter design of the iFlux|5 Elite are designed for the fine dust to cake on and the inner side of the filters and fall down into the bin as the mass grows. The filter surface area of the iFlux |5 Elite is 286 square feet. A typical 5HP dust collector has a surface area of 150 square feet. This increase in filter area translates to a large increase in airflow, making the iFlux an ideal machine for fine dust applications.

Quick Lever Wast Bins

The waste bins are easier to change than the kitchen garbage. Deactivate the air tight seal by pulling up the release bar and roll out the bin. The positive pressure design means there is no need for a bag hold down system like in multi-stage system. The wheels swivel 360 degrees and are mounted on a sturdy base to ensure they work in your shop for many many years.

Additional Features

The i|flux 5 Elite fine dust collector displays an amperage read out on the control panel. This allows the user to monitor the efficiency of the motor. A high frequency remote is also included standard so that the operator can turn the machine on and off with a 60 meter range.

Safety

There are several NFPA standards in place to ensure the proper installation and use of a dust collector. For woodworkers, the standard is NFPA 664: Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking Facilities. The i|Flux 5 Elite complies directly with this standard. In addition, the i|Flux is fitted with a phase controller and TEFC motor for added electrical safety.

 

Specifications:

  • Power Requirements: 220V/ 60Hz/ 3ph
  • Amperage: 14.4 Amps
  • Floor Space (W x L): 8.2′ x 3.74′
  • Machine Weight: 606.3 lbs (275 kgs)
  • Motor HP: 5
  • Motor RPM: 1720
  • Air Flow: 3991CFM at 5 inch wc
  • Inlet Diameter: 12 inch
  • Filter Area: 286.3 ft²
  • Filter Bag (L x D x H): 28 x 168 x 1800mm
  • Filter Bag Material: Polyester
  • Filter Cleaning: Manual Shaker
  • Waste Bin: EZ-lift Metal Bin 64 gal x 2
  • Shipping Weight: 723 lbs (328 kgs)
  • Shipping Dimensions (L x W x H): 75 x 39 x 80 inch

 

IFlux 5 Elite

 IFlux 10 Elite

The iFlux|10 Elite has solved this issue by using an appropriate filter arrangement with 409 square feet of surface area – double that of a typical 10HP collector. To do this, we used a smaller diameter bag, and a lot more of them. This arrangement maximizes the amount of surface area possible which is vital to adequate airflow through the collector. Keeping these filters clean was addressed in the design. The positive pressure chamber pushes the air through the filters as the dust falls in the EZ Lift waste bins. As the dust cakes on, it will fall into the bin. A shaking mechanism has been added to help release the caked dust. The i|Flux Elite series has been tested in the assembly line, and it is ready for all fine dust applications.

 

Airflow 5000CFM at 6”inchwc

The 15 inch inlet has a net airflow of 5000CFM with a static pressure of 6 inch wc. A typical CNC Router needs a minimum requirement of 1500CFM, while a typical 37 inch widebelt sander would call for a minimum 2000CFM. This makes the iFlux 10 a great fit for a CNC Router based cabinet shop that would be running several tools at once.

Fine Dust Ready

With fine dust, the key is to have a large filter surface area and to keep those filters clean. The smaller tube filter design of the iFlux|5 Elite are designed for the fine dust to cake on and the inner side of the filters and fall down into the bin as the mass grows. The filter surface area of the iFlux |5 Elite is 286 square feet. A typical 5HP dust collector has a surface area of 150 square feet. This increase in filter area translates to a large increase in airflow, making the iFlux an ideal machine for fine dust applications.

Quick Lever Wast Bins

The waste bins are easier to change than the kitchen garbage. Deactivate the air tight seal by pulling up the release bar and roll out the bin. The positive pressure design means there is no need for a bag hold down system like in multi-stage system. The wheels swivel 360 degrees and are mounted on a sturdy base to ensure they work in your shop for many many years.

Additional Features

The i|flux 5 Elite fine dust collector displays an amperage read out on the control panel. This allows the user to monitor the efficiency of the motor. A high frequency remote is also included standard so that the operator can turn the machine on and off with a 60 meter range.

Safety

There are several NFPA standards in place to ensure the proper installation and use of a dust collector. For woodworkers, the standard is NFPA 664: Standard for the Prevention of Fires and Explosions in Wood Processing and Woodworking Facilities. The i|Flux 5 Elite complies directly with this standard. In addition, the i|Flux is fitted with a phase controller and TEFC motor for added electrical safety.

 

Specifications:

  • Power Requirements: 220V/ 60Hz/ 3ph
  • Amperage: 24.8 Amps
  • Floor Space (W x L): 3424mm x 1140mm
  • Machine Weight: 1069 lbs (485 kgs)
  • Motor HP: 10
  • Motor RPM: 1720
  • Air Flow: 5000 CFM at 6 inch wc
  • Inlet Diameter: 15 inch
  • Filter Area: 409.3 ft²
  • Filter Bag (L x D x H): 28 x 168 x 1800mm
  • Filter Bag Material: Polyester
  • Filter Cleaning: Manual Shaker
  • Waste Bin: EZ-lift Metal Bin 64 gal x 3
  • Shipping Weight: 1113 lbs
  • Shipping Dimensions (L x W x H): 75 x 39 x 80 inch



 

X|Flux: 10HP

 XFlux 10HP

Features:
  • Motor HP: 10 HP
  • Phase: 3
  • Voltage: 220V
  • Amps: 28 Amps
  • Recommended Breaker: 50 AMP
  • Hertz: 60
  • Plug: No
  • RPM: 3450
  • Main Motor Switch: Radio Frequency
  • Control Panel: Anodized Aluminum

Specifications:

  • Hand Held Remote Control: HF (High Frequency)
  • LED Warning Light Empty Drum: Yes
  • Canister Auto Clean Controlled By Timer: Yes
  • Shop Setting CFM: 4700
  • Inlet CFM: 8070
  • Max Static Pressure (Inches of Water): 11 inch
  • Impeller/Fan Size: 15-1/2 inch
  • Impeller Material: Steel
  • Impeller Type: Radial Fin
  • Balancing of Fan: ISO 1940
  • Inlet Diameter: 12 inch
  • Drum Capacity: 54 Gal x 3
  • Octagon Drum: Low Pressure Suction, Swiveling Casters
  • Drum Collection Bag (Dia. x L): Plastic Bag 29 x 51 inch
  • Canister Filter Type: White 1 Micron
  • Filtration Efficiency: 0.2-2 Micron (at 99.97 percent)
  • MERV Rating: 12
  • Canister Diameter: 500mm (19.69 inch)
  • Canister Length: 900mm (35.43 inch)
  • Canister Cleaning: Timed Auto Clean 2 x 10 Seconds Per Work Hour
  • Canister Filter Lower: Plastic Bag 29″ x 24 inch
  • Wheels: 6 inch Industrial Swiveling
  • US/CSA Approved: Yes
  • Decibel Reading: 80dB(A)(at9.8′)
  • Assembled Dimensions (L x W x H): 104 x 49 x 106 inch
  • Machine Weight: 750 kgs/ 1653 lbs 
  • Shipping Weight: 830 kgs/ 1829 lbs

 

MDCTF52201
T|FLUX:5 INDUSTRIAL CYCLONE DUST COLLECTOR (LAGUNA INDUSTRIAL) SHIP WEIGHT: 948 LBS, MADE IN TAIWAN
Mfg. item #: MDCTF52201
LAGMDCTF52201
lease to own for as little as:$123 per month!
Free LTL Freight, Free Residential, Lift-gate & Call Ahead Appointment Service. Plus free shipping on all accessories added to the order.1046
$6,169.72

90
MDCTF102203
T|FLUX:10 INDUSTRIAL CYCLONE DUST COLLECTOR (LAGUNA INDUSTRIAL) SHIP WEIGHT: 1965 LBS, MADE IN TAIWAN
Mfg. item #: MDCTF102203
LAGMDCTF102203
lease to own for as little as:$184 per month!
Free LTL Freight, Free Residential, Lift-gate & Call Ahead Appointment Service. Plus free shipping on all accessories added to the order.1046
$9,197.21

90
MDCXF102203
X|FLUX:10 INDUSTRIAL CYCLONE DUST COLLECTOR (LAGUNA INDUSTRIAL) SHIP WEIGHT: 1829 LBS, MADE IN TAIWAN
Mfg. item #: MDCXF102203
LAGMDCXF102203
lease to own for as little as:$280 per month!
Free LTL Freight, Free Residential, Lift-gate & Call Ahead Appointment Service. Plus free shipping on all accessories added to the order.1046
$13,999.00

90
MDCIF52203
I|FLUX: 5 ELITE DUST COLLECTOR (LAGUNA INDUSTRIAL) SHIP WEIGHT: 723 LBS, MADE IN TAIWAN
Mfg. item #: MDCIF52203
LAGMDCIF52203
lease to own for as little as:$212 per month!
Free LTL Freight, Free Residential, Lift-gate & Call Ahead Appointment Service. Plus free shipping on all accessories added to the order.1046
$10,613.73

90
MDCIF102203
I|FLUX: 10 ELITE DUST COLLECTOR (LAGUNA INDUSTRIAL) SHIP WEIGHT: 1113 LBS, MADE IN TAIWAN
Mfg. item #: MDCIF102203
LAGMDCIF102203
lease to own for as little as:$280 per month!
Free LTL Freight, Free Residential, Lift-gate & Call Ahead Appointment Service. Plus free shipping on all accessories added to the order.1046
$13,999.00

90
Copyright © 2024 Smith-Hamilton, Inc
0.006 240412 15:03