Specifications:
- Blade Length: 34 inches
- Duel edge blade for double the cutting life
- Removable legs for ease of transportation
- Ideal for stone-coated shingle and shake style steel panels
- Weighs: 65lbs
|
|
|
Stone Coat Cutter Designed for use on a multitude of applications from stone coated metal shake and shingle to 14 gauge stainless flat sheet |
Sofit and Siding Shear The premier tabletop shear ideal for cutting siding, metal shingles or soffit. |
Straight Cut Shear
|
![]() |
![]() |
|
Heavy Duty Pivot Shear Straight Blade: Will shear straight at 90* and up to 2/12 gable 4/12 Gable Blade: Achieve between 3/12 – 5/12 gable 7/12 Gable Blade: Achieve between 6/12 – 8/12 gable |
Hip / Valley Roofing Shear Ideal for shearing heavy gauge exposed-fastener panels, with the ability to shear straight at 90 degrees and up to a 9/12 valley |
Blades last 15,000 - 20,000 cuts average siding contractor about 7 years
Click here to view Most Commonly Used Metal Roofing Profiles
Models and accessories | |
---|---|
SSC | Stone Coat Cutter Stone coat cutter for stone coated metal shake and shingle to 14 gauge stainless flat sheet |
MODEL20 | MODEL 20 - 20 inch SOFIT and SIDING SHEAR |
MODEL42 | MODEL 42 - 42 inch STRAIGHT CUT SHEAR |
HDPS |
Heavy Duty Pivot Shear Heavy Duty Pivot Shear for Straight and Gable Angles (Includes an interchangeable bladeset of your choice) |
HVRS |
Hip/Valley Roofing Shear Hip / Valley Roofing Shear for Straight, Gable, and Valley Angles (Includes an interchangeable bladeset of your choice) |
BLHD | Bladeset for HD Shear Additional bladeset for Heavy Duty Pivot Shear (Need Siding Profile) |
BLHV | Bladeset for HV Shear Additional bladeset for Hip/Valley Roofing Shear (Need Siding Profile) |
JIG | Jig Kit - Attaches to shear frame to assist in keeping panel |
![]() |
Stone Coat Cutter Referred to as the Swenson Shear utility knife. The Stone Coat Cutter is designed for use on a multitude of applications from stone coated metal shake and shingle to 14 gauge stainless flat sheet. Itâs equipped with a 34-inch blade that is made of long-lasting, high carbon steel. This go-to tool is safe, efficient and will give you a clean cut every time. Proudly designed and manufactured in the USA Specifications:
Now offering the All New Break and Bender, added to complement the One Arm Bandit. Full Panel with Hem on the Top Bender and can be used with any Manufacturers panel. Proudly Designed and Manufactured in the US |
![]() |
The Base and Ridge Bender A combination tool used for bending stone coated steel to control water from blowing into the roofing system. The ridge bender is used anywhere thereâs a short course in the field, head wall and ridge. The base bender bends stone coated steel panels at the rakes, side walls, hips and valley to control water from moving sideways into the roof. The Base and Ridge Bender was added to complement the Stone Coat Cutter. It can be used with any Manufacturers panel and is proudly designed and manufactured in the USA. Specifications:
|
*** Please indicate for a Valley or a Gable and Panel Profile ***
when Ordering a Swenson Shear !
Click here to view Most Commonly Used Metal Roofing Profiles
![]() |
Soffit Siding Shear M20 The Soffit and Siding Shear is the premier tabletop shear ideal for cutting siding, metal shingles or soffit. The 20 blade delivers a clean cut by eliminating burred edges and flying metal.
Specifications:
|
![]() |
Straight Cut Shear M42 Swenson Shear's Straight cut Shear is ideal for cutting exposed fastener panels at 90 degrees and can achieve up to a 2/12 gable with the same set of blades. This shear is user-friendly, lightweight and includes one custom blade set for the profile of your choice. Ordering this shear is as easy as letting us know who you buy your metal from and what panel profile(s) you offer. Are you doing more than one panel profile? No problem, this shear features interchangeable blades to accommodate more than one panel profile. Simply order the blade sets that will accommodate your multiple panel profiles. With the Straight cut shear you can count on a clean cut on your metal roof panel every time
|
|
The Heavy Duty Pivot Shear is user-friendly and guarantees a clean cut every time by eliminating burred edges and flying metal. Our shear was designed and manufactured in the USA and aims to make cutting exposed fastener panel as easy as possible. Straight Blade: Will shear straight at 90* and up to 2/12 gable 4/12 Gable Blade: Achieve between 3/12 â 5/12 gable 7/12 Gable Blade: Achieve between 6/12 â 8/12 gable The shear comes with one custom blade set of your choice. Each blade set is custom made to accommodate a specific profile and pitch however, the gable blades can be cheated 1/12 up or down from the blade set ordered. The base of the shear is built to accommodate these custom made interchangeable blades. In order to achieve an angled cut or accommodate multiple panel profiles, additional blade sets are required.
|
Specifications | |
---|---|
Common Blades | Capabilities |
Straight Blade | Will shear straight at 90 deg and do up to a 2/12 gable |
4/12 Gable Blade: | Achieve between a 3/12-5/12 gable |
7/12 Gable Blade: | Achieve between a 6/12-8/12 gable |
Specifications : Used for Straight Cuts and Gable Cuts | |
Panel Sizes: | Can shear exposed fastener panel up to 48 inch in width |
Recommended Panel Thickness: | 24 Gauge |
Ideal For: | Straight cuts and gable angles |
Interchangeable Blade Sets: | The blade sets can be changed to accommodate any manufacturers panel profile. |
Blades: | Blades are custom made to match the exposed fastener panel profile needed. Separate blades will be needed for each panel profile or to achieve various angle cuts. |
Cuts Achievable: | Can cut straight at 90 degree and up to a 8/12 gable with additional blade sets. |
Switching Blades: | Switching between blade sets takes only a few minutes. All that is needed is 3/16 inch Allen Wrench and 1/2 inch wrench. |
Lifetime of Blades: | Blades have been shown to last for thousands of cuts with proper care. |
*** Please indicate for a Valley or a Gable and Panel Profile ***
when Ordering a Swenson Shear !
Click here to view Most Commonly Used Metal Roofing Profiles
|
Hip / Valley Roofing Shear The Hip and Valley Roofing is the optimal shear for cutting your hips and valleys up to 64 inch wide. It eliminates burred edges and flying metal. It was designed and manufactured in the USA and aims to make cutting exposed fastener panel as easy as possible. This tool is ideal for shearing heavy gauge exposed-fastener panels, with the ability to shear straight at 90 degrees and up to a 9/12 valley. The shear is transportable and weighs 160lbs. The Shear comes with one custom blade set of your choice. Each blade set is custom made to accommodate a specific profile and pitch. The base of the shear is built to accommodate these custom made interchangeable blades. When needing to cut a different profile, additional blade sets are available. |
Specifications | |
---|---|
Blade Information | Capabilities |
Straight Blade: | Will shear straight at 90 degree and do up to a 2/12 gable |
Valley Blades: | A separate blade set will be needed for each valley angle |
Ideal For: | Valley angles |
Interchangeable Blade Sets: |
The blade sets can be changed to accommodate any manufacturers panel profile. Separate blades will be needed for each panel profile or to achieve various valley angles. |
Max Cut Width: | Can shear exposed fastener panel up to 64 inch in width |
Recommended Panel Thickness: | 24 gauge |
Blades: | Each shear comes with one set of blades attached to the shear. Blades are custom made to match the exposed fastener panel profile needed. |
Cuts Achievable: | Can cut straight at 90 degree and up to a 9/12 valley with additional blade sets. |
Switching Blades: | Switching between blade sets takes only a few minute. All that is needed is 3/16 inch Allen Wrench and 1/2 inch wrench |
Lifetime of Blades: | Blades have been shown to last for thousands of cuts with proper care. |
*** Please indicate for a Valley or a Gable and Panel Profile ***
when Ordering a Swenson Shear !
Click here to view Most Commonly Used Metal Roofing Profiles
Click here to view Most Commonly Used Metal Roofing Profiles
*** Please indicate for a Valley or a Gable and Panel Profile ***
when Ordering a Swenson Shear !
These are samples only - please indicate what profile your cutting
we can make ANY metal profile
M48 Blades:
M64 Blades
Blade Profiles Included | |
---|---|
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
![]() |
STONE COAT CUTTER FOR STONE COATED METAL SHAKE AND SHINGLE TO 14 GAUGE STAINLESS FLAT SHEET
HEAVY DUTY PIVOT SHEAR FOR STRAIGHT AND GABLE ANGLES *INCLUDES AN INTERCHANGEABLE BLADESET OF YOUR CHOICE
HIP/VALLEY ROOFING SHEAR FOR STRAIGHT, GABLE, AND VALLEY ANGLES *INCLUDES AN INTERCHANGEABLE BLADESET OF YOUR CHOICE
ADDITIONAL BLADESET FOR HEAVY DUTY PIVOT SHEAR (NEED SIDING PROFILE)
ADDITIONAL BLADESET FOR HIP/VALLEY ROOFING SHEAR (NEED SIDING PROFILE)